IGNITION SYSTEM ON-VEHICLE INSPECTION

PROCEDURE


  1. PERFORM SPARK PLUG

    Tech Tips

    Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug.



    1. Check for DTCs.


      Note

      If any DTCs are output, perform troubleshooting procedure for those DTCs.

    2. Remove the 4 ignition coil assemblies and 4 spark plugs.

      Click here

      Note


      • If an ignition coil assembly has been struck or dropped, replace it.

      • If a spark plug has been struck or dropped, replace it.

      Tech Tips

      Arrange the removed parts in the correct order.

    3. A01MRLV

      Disconnect the fuel injector assembly connector.

    4. Disconnect the injector driver connector.

    5. Install the spark plug into the ignition coil assembly, and then connect the ignition coil assembly connector.

    6. Put the engine in inspection mode (maintenance mode).

      Click here

    7. Ground the spark plug.

    8. Check that spark occurs at each spark plug while the engine is being cranked.

      Note


      • Be sure to ground the spark plugs when checking them.

      • Do not crank the engine for more than 2 seconds.

      • If an ignition coil assembly has been struck or dropped, replace it.

      • If a spark plug has been struck or dropped, replace it.

      Tech Tips

      If spark does not occur, perform the following procedure.

    9. Connect the injector driver connector.

    10. Connect the fuel injector assembly connector.

    11. Install the 4 spark plugs and 4 ignition coil assemblies.

      Click here

      Note


      • If a spark plug has been struck or dropped, replace it.

      • If an ignition coil assembly has been struck or dropped, replace it.

      Tech Tips

      Install the same parts to their original positions.

    12. Check for DTCs.


    13. Clear the DTCs.


  2. INSPECT IGNITION COIL ASSEMBLY AND SPARK TEST

    Tech Tips

    Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug.



    1. Check that the ignition coil assembly connector is securely connected.

      Result
      Result Action
      NG Connect securely
      OK Go to next step

    2. Perform a spark test on each ignition coil assembly.


      1. Replace the ignition coil assembly with a known good one.

      2. Perform the spark test again.

        Result
        Result Action
        NG Go to next step
        OK Replace ignition coil assembly

    3. Perform a spark test on each spark plug.


      1. Replace the spark plug with a known good one.

      2. Perform the spark test again.

        Result
        Result Action
        NG

        Inspect the ignition system
        OK Replace spark plug

        Note


        • If an ignition coil assembly has been struck or dropped, replace it.

        • If a spark plug has been struck or dropped, replace it.

    4. Connect the injector driver connector.

    5. Connect the fuel injector assembly connector.

    6. Install the 4 spark plugs and 4 ignition coil assemblies.

      Click here

      Note


      • If a spark plug has been struck or dropped, replace it.

      • If an ignition coil assembly has been struck or dropped, replace it.

      Tech Tips

      Install the same parts to their original positions.

    7. Check for DTCs.


    8. Clear the DTCs.


  3. INSPECT SPARK PLUG

    Note


    • Do not use a wire brush for cleaning.

    • Do not adjust the electrode gap of a used spark plug.

    Tech Tips

    Perform "Inspection After Repair" after replacing a spark plug.



    1. A01MSDXC12
      *a Ground

      Check the electrode.


      1. Using a megohmmeter, measure the insulation resistance.

        Standard Insulation Resistance
        Tester Connection Condition Specified Condition
        Spark plug (terminal part) - Body ground Always 10 MΩ or higher

        Tech Tips


        • If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

        • If a megohmmeter is not available, perform the following simple inspection instead.

    2. Alternative inspection method.


      1. Put the engine in inspection mode (maintenance mode).

        Click here

      2. Start the engine.

        Note

        Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).

      3. Quickly accelerate the engine to 2500 rpm 5 times.

        Note

        Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected).

      4. Remove the spark plug.

        Click here

      5. Visually check the spark plug.

        Tech Tips

        If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.

    3. Check the spark plug for any damage to its threads and insulator.

      If there is any damage, replace the spark plug.

      Recommended Spark Plug
      Manufacturer Spark Plug Type
      DENSO FK20HBR8
    4. A01MTPMC04
      *a Spark Plug Electrode Gap

      Check the spark plug electrode gap.

      Maximum Electrode Gap for Used Spark Plug
      1.1 mm (0.0433 in.)

      Note

      Never attempt to adjust the electrode gap of a used spark plug.

      If the electrode gap is more than the maximum, replace the spark plug.

      Electrode Gap for New Spark Plug
      0.7 to 0.8 mm (0.0276 to 0.0315 in.)
    5. A01MSZR

      Clean the spark plugs.

      If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

      Standard Air Pressure
      588 kPa (6.0 kgf/cm2, 85 psi)
      Standard Duration
      20 seconds or less

      Tech Tips

      Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.

    6. Install the spark plug.

      Click here

  4. PERFORM INITIALIZATION


    1. Perform "Inspection After Repair" after replacing an ignition coil assembly or spark plug.