SFI SYSTEM(w/o EGR System), Diagnostic DTC:P060B

DTC Code DTC Name
P060B Internal Control Module A/D Processing Performance

MONITOR DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P060B Internal Control Module A/D Processing Performance An ECM main CPU communication error (1 trip detection logic).

  • ECM

  • Knock control sensor

 Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the power switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the GTS off.

  5. Turn the power switch off.

  6. Disconnect the GTS.

  7. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

  8. Connect the cable to the negative (-) auxiliary battery terminal.

  9. Connect the GTS to the DLC3.

  10. Turn the power switch on (IG) and turn the GTS on.

  11. Wait 16 seconds or more.

  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  13. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  15. Input the DTC: P060B.

  16. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

CAUTION / NOTICE / HINT

Note

After turning power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ OUTPUT DTC (DTC P060B)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the power switch off.

    6. Turn the GTS off.

    7. Disconnect the GTS.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for 1 minute.

    9. Connect the cable to the negative (-) auxiliary battery terminal.

    10. Connect the GTS to the DLC3.

    11. Turn the power switch on (IG).

    12. Turn the GTS on.

    13. Wait 16 seconds or more.

    14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    15. Read the DTCs.

      Click here


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC is not output A
      DTC P060B is output B
      DTC P060B and P0327, P0328 are output C

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here

    C

    GO TO DTC P0327, P0328 Click here