AIR CONDITIONING SYSTEM, Diagnostic DTC:B1475/75

DTC Code DTC Name
B1475/75 A/C Inverter Cooling / Heating System Malfunction

DESCRIPTION

The temperature sensor of the compressor with motor assembly detects the A/C inverter temperature.

If the temperature exceeds the maximum, operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1475/75 A/C Inverter Cooling / Heating System Malfunction Temperature of the A/C inverter is outside the specified range (temperature is too high), or there is an open or short to ground in the temperature sensor circuit

  • Cooling fan system

  • Refrigerant volume

  • Compressor with motor assembly

  • CAN communication system

 Memorized

CAUTION / NOTICE / HINT

CAUTION:


  • Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

  • Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

Note


  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  • The hybrid control system and air conditioning system output DTCs separately. Perform troubleshooting for the hybrid control system first if DTCs from these systems are output simultaneously.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Using the GTS, check if the CAN communication system is functioning normally.

      Click here

      Result
      Result Proceed to
      CAN communication system DTCs are not output A
      CAN communication system DTCs are output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test.

    5. Check the operation by referring to the table below.


      Powertrain > Engine and ECT > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Control the Electric Cooling Fan Control electric cooling fan motor ON/OFF

      Perform this test when the following conditions are met:


      • Power switch on (IG)

      • Engine stopped

      • Shift lever in P

      Powertrain > Engine and ECT > Active Test
      Tester Display
      Control the Electric Cooling Fan
      OK
      Electric cooling fan operates smoothly.
      Result
      Proceed to
      OK
      NG

    NG

    GO TO COOLING FAN SYSTEM Click here

    OK

  3. CHECK REFRIGERANT PRESSURE


    1. Install a manifold gauge set.

      Click here

    2. Turn the power switch on (READY).

    3. A0020CP

      Read the manifold gauge pressure when the following conditions are met.


      1. Prepare the vehicle according to the table below.

        Item Condition
        Vehicle doors Fully open
        Temperature setting MAX COLD
        Blower speed HI
        A/C switch On
        Recirculation/fresh switch RECIRCULATION
        Interior temperature 25 to 35°C (77 to 95°F)
      Standard Pressure
      Low pressure side
      150 to 250 kPa (1.5 to 2.5 kgf/cm2, 22 to 36 psi)
      High pressure side
      1370 to 1570 kPa (14 to 16 kgf/cm2, 199 to 228 psi)
      Result
      Proceed to
      OK
      NG

    NG

    CHARGE REFRIGERANT Click here

    OK

  4. READ OUTPUT DTC (DTC B1475/75)


    1. Clear the DTCs.

      Click here


      Body Electrical > Air Conditioner > Clear DTCs

    2. Turn the power switch on (READY).

    3. Prepare the vehicle according to the table below.

      Item Condition
      Blower speed HI
      A/C switch On
      Temperature setting MAX. COLD

    4. Check for DTCs.

      Click here


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTC B1475/75 is not output (normal) A
      DTC B1475/75 is output B

      Note

      If the engine keeps idling when ambient temperature is high, the compressor with motor assembly may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.


    A

    SYSTEM IS OK

    B

    REPLACE COMPRESSOR WITH MOTOR ASSEMBLY Click here