REAR SEAT OUTER BELT ASSEMBLY INSTALLATION

PROCEDURE

INSPECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

Click here
INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY
1. w/o Pretensioner:
  1. Engage the guide and install the rear seat 3 point type outer belt assembly with the bolt.
    
    Torque:
    
    42 N*m { 428 kgf*cm, 31 ft.*lbf }
2. *a Locking Button
  
  *b Lock
  
  w/ Pretensioner:
  1. Temporarily install the rear seat 3 point type outer belt assembly with the 2 bolts.
  2. Fully tighten the bolt (A) first, then the bolt (B).
    
    Torque:
    
    Bolt (A)
    
    7.5 N*m { 76 kgf*cm, 66 in.*lbf }
    
    Bolt (B)
    
    42 N*m { 428 kgf*cm, 31 ft.*lbf }
  3. Connect the pretensioner connector and lock the locking button as shown in the illustration.
    
    Note
    
    Securely lock the locking button.
3. Check that the ELR locks.
  
  Note
  
  The check should be performed with the rear seat 3 point type outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)
1. for Fixed Seat Type:
  1. Pass the 3 rear seat belt floor anchors through the holes of the package tray trim panel assembly.
2. for Fold Down Seat Type:
  1. Pass the 2 rear seat belt floor anchors through the holes of the package tray trim panel assembly.
3. Engage the 5 guides and 3 clips to install the package tray trim panel assembly.
4. Install the 4 clips.
INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)
1. Pass the 2 rear seat belt floor anchors through the holes of the package tray trim panel assembly.
2. Engage the guide and 3 clips to install the package tray trim panel assembly.
3. Install the 4 clips.
INSTALL CENTER STOP LIGHT ASSEMBLY WITH COVER (w/o Rear Sunshade)

Click here
INSTALL REAR SEAT SHOULDER BELT HOLE COVER
Tech Tips

Use the same procedure for all rear seat shoulder belt hole covers.
1. Engage the 2 guides and 2 claws to install the rear seat shoulder belt hole cover.
CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Fixed Seat Type)

Click here
CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH
1. *a Protruding Part
  
  Connect the floor anchor of the rear seat 3 point type outer belt assembly LH with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat 3 point type outer belt assembly LH to overlap the protruding parts of the floor panel.
CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL NO. 3 ROOM PARTITION COVER (for Fold Down Seat Type)
1. Engage the 5 clips to install the No. 3 room partition cover.
INSTALL NO. 2 ROOM PARTITION COVER (for Fold Down Seat Type)
1. Engage the guide.
2. Engage the 2 claws and clip to install the No. 2 room partition cover.
3. Install the clip.
INSTALL NO. 1 ROOM PARTITION COVER (for Fold Down Seat Type)

Tech Tips

Use the same procedure as for the No. 2 room partition cover.
INSTALL REAR SEAT SUB FLOOR PANEL (for Fold Down Seat Type)
1. Engage the 3 clips to install the rear seat sub floor panel.
INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER (for Fold Down Seat Type)

Click here
INSTALL LUGGAGE COMPARTMENT FLOOR MAT (for Fold Down Seat Type)

Click here
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH

Click here
INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR SEAT SIDE GARNISH LH

Click here
INSTALL REAR SEAT SIDE GARNISH RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR DOOR SCUFF PLATE LH

Click here
INSTALL REAR DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)

Click here
INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Click here

*a	Locking Button
*b	Lock