FRONT POWER SEAT CONTROL SYSTEM(w/ Memory), Diagnostic DTC:B2650

DTC Code DTC Name
B2650 Slide Sensor Malfunction

DESCRIPTION

When the front power seat switch (driver seat) does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2650 Slide Sensor Malfunction The forward and backward lock detection position of the sensor is the same.

  • Front power seat switch (driver seat)

  • Slide motor (Front seat adjuster assembly (driver seat))

  • Wire harness or connector

WIRING DIAGRAM

A002116E03

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Driver Seat > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Driver Seat > Trouble Codes
      OK
      DTC B2650 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  3. PERFORM ACTIVE TEST USING GTS (SLIDE MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Driver Seat / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Driver Seat > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Seat Slide Operation Seat slide operation OFF/Rear/Front -

      Body Electrical > Driver Seat > Active Test
      Tester Display
      Seat Slide Operation
      OK
      Motor operates normally.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)) Click here

    OK

  4. CHECK FRONT POWER SEAT SWITCH (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)


    1. Disconnect the b9*1 or a1*2 slide motor (front seat adjuster assembly (driver seat)) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      b9-2 (O/P) - b9-3 (GND) Slide switch on 4.8 to 5.1 V
      for RHD
      Tester Connection Condition Specified Condition
      a1-2 (O/P) - a1-3 (GND) Slide switch on 4.8 to 5.1 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))) Click here

    OK

  5. CHECK SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))


    1. A0022K8C06
      *A for LHD
      *B for RHD
      *a

      Component with harness connected

      (Slide Motor (Front Seat Adjuster Assembly (Driver Seat))

      Reconnect the b9*1 or a1*2 slide motor (front seat adjuster assembly (driver seat)) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      b9-2 (O/P) - Body ground Slide motor operating 4.5 to 4.8 V
      for RHD
      Tester Connection Condition Specified Condition
      a1-2 (O/P) - Body ground Slide motor operating 4.5 to 4.8 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER SEAT SWITCH (DRIVER SEAT) Click here

    NG

    REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)) Click here

  6. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))


    1. Disconnect the b12*1 or a7*2 front power seat switch (driver seat) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      b12-5 (SSRS) - b9-2 (O/P) Always Below 1 Ω
      b12-5 (SSRS) - Body ground Always 10 kΩ or higher
      b9-2 (O/P) - Body ground Always 10 kΩ or higher
      b12-1 (SGND) - b9-3 (GND) Always Below 1 Ω
      b12-1 (SGND) - Body ground Always 10 kΩ or higher
      b9-3 (GND) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      a7-5 (SSRS) - a1-2 (O/P) Always Below 1 Ω
      a7-5 (SSRS) - Body ground Always 10 kΩ or higher
      a1-2 (O/P) - Body ground Always 10 kΩ or higher
      a7-1 (SGND) - a1-3 (GND) Always Below 1 Ω
      a7-1 (SGND) - Body ground Always 10 kΩ or higher
      a1-3 (GND) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER SEAT SWITCH (DRIVER SEAT) Click here

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR

  7. INSPECT SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT))


    1. Remove the front seat adjuster assembly (driver seat).

      Click here

    2. Inspect the front seat adjuster assembly (driver seat) (slide motor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)) Click here

    OK

  8. CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))


    1. Disconnect the b4*1 or a6*2 front power seat switch (driver seat) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      b4-3 (SLD+) - b9-4 (FWD) Always Below 1 Ω
      b4-3 (SLD+) - Body ground Always 10 kΩ or higher
      b9-4 (FWD) - Body ground Always 10 kΩ or higher
      b4-4 (SLD-) - b9-1 (BACK) Always Below 1 Ω
      b4-4 (SLD-) - Body ground Always 10 kΩ or higher
      b9-1 (BACK) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      a6-3 (SLD+) - a1-4 (FWD) Always Below 1 Ω
      a6-3 (SLD+) - Body ground Always 10 kΩ or higher
      a1-4 (FWD) - Body ground Always 10 kΩ or higher
      a6-4 (SLD-) - a1-1 (BACK) Always Below 1 Ω
      a6-4 (SLD-) - Body ground Always 10 kΩ or higher
      a1-1 (BACK) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER SEAT SWITCH (DRIVER SEAT) Click here

    NG

    REPAIR OR REPLACE HARNESS AND CONNECTOR