FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connector to the front seat airbag assembly under the front seat assembly.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        A0020FOC01
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    6. A0020JBN01

      Tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      36.8 N*m  { 375 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    7. Lift up the seat track adjusting handle and move the front seat assembly to the foremost position.

    8. A0020CMN01

      Tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      36.8 N*m  { 375 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSPECT SEAT SLIDE ADJUSTER LOCK


    1. While performing sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.

  3. INSTALL INNER SEAT TRACK BRACKET COVER


    1. Lift up the seat track adjusting handle and move the front seat assembly to the foremost position.

    2. Engage the 2 claws to install the inner seat track bracket cover.

  4. INSTALL REAR OUTER FRONT SEAT TRACK COVER


    1. Engage the 2 claws to install the rear outer front seat track cover.

  5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    2. Engage the 2 claws to install the front inner seat track bracket cover.

  6. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. Engage the 2 claws to install the front outer seat track bracket cover.

  7. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly.

  8. CONNECT FRONT SEAT OUTER BELT ASSEMBLY

    Click here

  9. INSTALL SEAT BELT ANCHOR COVER CAP

    Click here

  10. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

    Click here

  11. INSTALL BATTERY SERVICE HOLE COVER LH

    Click here

  12. CHECK SEAT HEATER (w/ Seat Heater System)

    Click here

  13. INSPECT SRS WARNING LIGHT

    Click here