FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL SEAT BELT HOLE COVER


    1. Engage the claw to install the seat belt hole cover to the front seat adjuster assembly.

  2. INSTALL SEAT TRACK ADJUSTING HANDLE


    1. A011O29

      Engage the 2 springs to install the seat track adjusting handle to the front seat adjuster assembly.

  3. INSTALL FRONT SEAT CUSHION SPRING


    1. Engage the 6 hooks to install the front seat cushion spring to the front seat adjuster assembly.

  4. INSTALL FRONT SEATBACK HOOK


    1. Install the 2 front seatback hooks to the front seatback spring sub-assembly.

  5. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY


    1. Engage the 2 guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly.

    2. Engage the 2 claws.

  6. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. Engage each claw to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.

  7. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    1. Engage the 4 guides to install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly.

    2. Install the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  8. INSTALL FRONT SEAT WIRE (w/ Seat Heater System)


    1. Engage each claw and each clamp to install the front seat wire.

  9. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH


    1. A011NI4

      Engage the 3 claws to install the front seat cushion edge protector LH.

    2. Install the screw.

  10. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  11. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. A011Q4MN01

      Engage the clip B to install the front seat lower cushion shield LH.

    2. Engage the hook as shown in the illustration.

    3. Engage the clip A.

  12. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH


    1. Engage the clip to install the front seat lower cushion shield RH.

    2. Engage the hook as shown in the illustration.

    3. A011Q49

      Install the screw.

  13. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. Engage the guide to install the reclining adjuster inside cover LH.

  14. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A011OJM

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 14 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    2. A011M5IC01
      B003Y0W Fastener

      Engage the 2 fasteners.

  16. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    Click here

  17. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. A011MMRC01
      *a Bracket

      Engage the 3 brackets and install the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Install the brackets securely.

  18. INSTALL FRONT SEAT HEADREST SUPPORT


    1. Engage each claw to install the 2 front seat headrest supports.

    2. A011PBE

      Close the 2 fasteners.

    3. A011QII

      Using hog ring pliers, install 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. A011Q2B

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. A011MT8

      Pass the 2 fasteners through the tabs as shown in the illustration.

  19. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A011NZP

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    2. A011PHR

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

  20. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type front seat cushion cover with pad.

    2. A011Q3R

      Engage the 11 hooks.

    3. for Front Passenger Side:


      1. A011PTK

        Engage the claw to install the connector.

    4. w/ Seat Heater System:


      1. A011LZ8

        Connect the connector.

      2. Engage the 3 clamps.

      3. A011NJY

        Engage the clamp.

      4. Connect the connector.

    5. A011PXKC01
      B003Y0W Fastener

      Engage the fastener to secure the front seat airbag assembly wire harness.

  21. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. A011NLX

      Engage the 5 claws and 6 guides to install the front seat inner cushion shield.

  22. INSTALL FRONT SEAT CUSHION SHIELD


    1. A011PBM

      Engage the 5 claws, 6 guides and clip to install the front seat cushion shield.

    2. A011M7K

      Install the screw.

  23. INSTALL VERTICAL ADJUSTER COVER


    1. Engage the 2 guides to install the vertical adjuster cover to the vertical seat release arm.

  24. INSTALL VERTICAL SEAT RELEASE ARM


    1. Install the vertical seat release arm with the 2 screws.

    2. A011P9V

      Engage the guide.

  25. INSTALL SEAT ADJUSTER COVER


    1. Engage the 2 claws and 2 guides to install the seat adjuster to the front seat cushion shield.

  26. INSTALL VERTICAL ADJUSTING HANDLE


    1. Engage the claw to install the vertical adjusting handle.

  27. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    1. Engage the claw to install the reclining adjuster release handle.

  28. CONNECT SEPARATE TYPE FRONT SEATBACK COVER


    1. Connect the rubber band of the separate type front seatback cover.

  29. INSTALL SEAT ADJUSTER COVER CAP


    1. Install the 2 seat adjuster cover caps.

  30. INSTALL FRONT SEAT INNER BELT ASSEMBLY

    Click here

  31. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    Click here

  32. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  33. INSTALL NO. 1 SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)

    Click here