FRONT SEAT ASSEMBLY(for Manual Seat) DISASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. REMOVE NO. 1 SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)

    Click here

  2. REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  3. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

    Click here

  4. REMOVE FRONT SEAT INNER BELT ASSEMBLY

    Click here

  5. REMOVE SEAT ADJUSTER COVER CAP


    1. A011PA3

      Remove the 2 seat adjuster cover caps.

  6. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER


    1. A011N6S

      Disconnect the rubber band of the separate type front seatback cover.

  7. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    1. A011N0MC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.

  8. REMOVE VERTICAL ADJUSTING HANDLE


    1. A011QGQC01
      *a Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the vertical adjusting handle.

  9. REMOVE SEAT ADJUSTER COVER


    1. A011LXF

      Disengage the 2 claws and 2 guides to remove the seat adjuster cover from the front seat cushion shield.

  10. REMOVE VERTICAL SEAT RELEASE ARM


    1. A011P9V

      Disengage the guide.

    2. A011PKM

      Remove the 2 screws and vertical seat release arm.

  11. REMOVE VERTICAL ADJUSTER COVER


    1. A011OSB

      Disengage the 2 guides to remove the vertical adjuster cover from the vertical seat release arm.

  12. REMOVE FRONT SEAT CUSHION SHIELD


    1. A011M7K

      Remove the screw.

    2. A011PBM

      Disengage the 5 claws, 6 guides and clip to remove the front seat cushion shield.

  13. REMOVE FRONT SEAT INNER CUSHION SHIELD


    1. A011NLX

      Disengage the 5 claws and 6 guides to remove the front seat inner cushion shield.

  14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. A011PXKC01
      B003Y0W Fastener

      Disengage the fastener and separate the front seat airbag assembly wire harness.

    2. w/ Seat Heater System:


      1. A011NJY

        Disconnect the connector.

      2. Disengage the clamp.

      3. A011LZ8

        Disengage the 3 clamps.

      4. Disconnect the connector.

    3. for Front Passenger Side:


      1. A011PTK

        Disengage the claw to remove the connector.

    4. A011Q3R

      Disengage the 11 hooks and remove the separate type front seat cushion cover with pad.

  15. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A011NVT

      Remove the 2 hog rings.

    2. A011ONX

      Remove the 18 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

  16. REMOVE FRONT SEAT HEADREST SUPPORT


    1. A011MT8

      Pull out the 2 fasteners.

    2. A011QCR

      Remove the 2 hog rings.

    3. A011MDJ

      Remove the 3 hog rings.

    4. A011PBE

      Open the 2 fasteners.

    5. A011MHY

      Disengage each claw and remove the 2 front seat headrest supports.

  17. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. A011MMRC01
      *a Bracket

      Remove the 2 nuts and disengage the 3 brackets.

    2. Remove the separate type front seatback cover with pad.

  18. REMOVE FRONT SEAT AIRBAG ASSEMBLY

    Click here

  19. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. A011M5IC01
      B003Y0W Fastener

      Disengage the 2 fasteners.

    2. A011MMX

      Remove the 14 hog rings to remove the separate type front seatback cover from the separate type front seatback pad.

  20. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    1. A011PMF

      Disengage the guide to remove the reclining adjuster inside cover LH.

  21. REMOVE RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Perform the same procedure as for the LH side.

  22. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH


    1. A011O4FN01

      Disengage the clip A.

    2. Disengage the hook as shown in the illustration.

    3. Disengage the clip B to remove the front seat lower cushion shield LH.

  23. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH


    1. A011ON1

      Remove the screw.

    2. Disengage the hook as shown in the illustration.

    3. Disengage the clip to remove the front seat lower cushion shield RH.

  24. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR LH


    1. A011NI4

      Remove the screw.

    2. Disengage the 3 claws to remove the front seat cushion edge protector LH.

  25. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  26. REMOVE FRONT SEAT WIRE (w/ Seat Heater System)


    1. Disengage each claw and each clamp to remove the front seat wire.

  27. REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    1. A011QHU

      Remove the 4 bolts.

    2. Disengage the 4 guides to remove the separate type front seatback spring assembly from the separate type front seat cushion spring assembly.

  28. REMOVE FRONT SEATBACK EDGE PROTECTOR


    1. A011OO3

      Disengage each claw to remove the 2 front seatback edge protectors from the front seatback frame sub-assembly.

  29. REMOVE FRONT SEATBACK SPRING SUB-ASSEMBLY


    1. A011NXE

      Disengage the 2 claws.

    2. Disengage the 2 guides to remove the front seatback spring sub-assembly from the front seatback frame sub-assembly.

  30. REMOVE FRONT SEATBACK HOOK


    1. Remove the 2 front seatback hooks from the front seatback spring sub-assembly.

  31. REMOVE FRONT SEAT CUSHION SPRING


    1. A011OXN

      Disengage the 6 hooks to remove the front seat cushion spring from the front seat adjuster assembly.

  32. REMOVE SEAT TRACK ADJUSTING HANDLE


    1. A011O29

      Disengage the 2 springs to remove the seat track adjusting handle from the front seat adjuster assembly.

  33. REMOVE SEAT BELT HOLE COVER


    1. A011PZZ

      Disengage the claw and remove the seat belt hole cover from the front seat adjuster assembly.