FRONT SEAT ASSEMBLY(for Manual Seat) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.

  • If the front seat airbag assembly was deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. REMOVE BATTERY SERVICE HOLE COVER LH

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE SEAT BELT ANCHOR COVER CAP

    Click here

  5. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY

    Click here

  6. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. Remove the front seat headrest assembly from the front seat assembly.

  7. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER


    1. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    2. A0022OI

      Disengage the 2 claws to remove the front outer seat track bracket cover.

  8. REMOVE FRONT INNER SEAT TRACK BRACKET COVER


    1. A00210K

      Disengage the 2 claws to remove the front inner seat track bracket cover.

  9. REMOVE REAR OUTER FRONT SEAT TRACK COVER


    1. Lift up the seat track adjusting handle and move the front seat assembly to the foremost position.

    2. A0021KJ

      Disengage the 2 claws to remove the rear outer front seat track cover.

  10. REMOVE INNER SEAT TRACK BRACKET COVER


    1. A0020PQ

      Disengage the 2 claws to remove the inner seat track bracket cover.

  11. REMOVE FRONT SEAT ASSEMBLY


    1. A0020CM

      Remove the 2 bolts on the rear side of the front seat assembly.

    2. Lift up the seat track adjusting handle and move the front seat assembly to the rearmost position.

    3. A0020JB

      Remove the 2 bolts on the front side of the front seat assembly.

    4. Operate the vertical adjusting handle and move the front seat assembly to the uppermost position.

    5. Lift up the seat track adjusting handle and move the front seat assembly to the center position.

    6. Operate the reclining adjuster release handle and move the seatback to the upright position.

    7. Disconnect the connector from the front seat airbag assembly under the front seat assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. A00216SC10
        *a White Housing Lock
        *b Yellow CPA
        *c Slide

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    8. Disconnect each connector and disengage each clamp under the front seat assembly.

    9. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.