DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Wiper Information | Wiper operational status | Unoperat, Oil off, Mist, Washer, Unknown, Intermi, Lo or Hi | The respective operational status displayed | - |
| PCS OFF Switch | Pre-crash safety system cancel switch assembly status | ON or OFF | ON: Pre-crash safety system cancel switch assembly on OFF: Pre-crash safety system cancel switch assembly off |
- |
| Pre-Crash System | Pre-crash safety system control | Valid or Inval | Valid: Pre-crash safety system control possible Inval: Pre-crash safety system control not possible |
- |
| PCS Indicator | "Check PCS System" display request signal | ON or OFF | ON: "Check PCS System" display requested OFF: "Check PCS System" display not requested |
- |
| PCS Disabled Indicator | "PCS temporarily not available" display request signal | ON or OFF | ON: "PCS temporarily not available" display requested OFF: "PCS temporarily not available" display not requested |
- |
| Pre-Crash Safety Warning Buz | Pre-crash safety system warning buzzer | Valid or Inval | Valid: Pre-crash safety system warning buzzer operation possible Inval: Pre-crash safety system warning buzzer operation not possible |
- |
| Pre-Crash Brake | Pre-crash brake function | Valid or Inval | Valid: Pre-crash brake operation possible Inval: Pre-crash brake operation not possible |
- |
| PBA Start | Pre-crash brake assist activation signal | OFF, Standby, Assist Lv1 or Assist Lv2 | OFF: Pre-crash brake assist not activated Standby: Pre-crash brake assist standby Assist Lv1: Pre-crash brake assist activated Assist Lv2: Pre-crash brake assist activated |
Signal status changes when the pre-crash safety brake assist is activated before a crash (Pre-crash brake will activate only in situations where the driver depresses the brake pedal) |
| Brake Assist Standby | Supplemental brake pressure signal | ON or OFF | ON: Supplemental brake pressure being provided OFF: Supplemental brake pressure not being provided |
Signal status changes when supplemental brake pressure is being provided after a crash is judged as unavoidable and before the brake pedal is depressed |
| Pre-Crash Brake Control | Pre-crash brake operational status | ON or OFF | ON: Pre-crash brake operating OFF: Pre-crash brake not operating |
Status changes when pre-crash safety brake operates before a crash |
| AVS Start | Adaptive variable suspension system control activation status | ON or OFF | ON: Adaptive variable suspension system control activated OFF: Adaptive variable suspension system control not activated |
|
| CCS Cancel | Automatic cancellation of cruise control during pre-crash safety brake activation | ON or OFF | ON: Cruise control automatically canceled OFF: Cruise control not automatically canceled |
- |
| Pre-Crash Safety Brake Ind | Pre-crash safety system "BRAKE!" alert status | ON or OFF | ON: Pre-crash safety system "BRAKE!" alert on OFF: Pre-crash safety system "BRAKE!" alert off |
- |
| Front Radar-Dirt History | Millimeter wave radar sensor assembly dirt history | ON or OFF | ON: History of excessive dirt OFF: No history of excessive dirt |
- |
| Front Radar-Environment Hist | Millimeter wave radar sensor assembly environment condition history | Good or Bad | Good: No history of excessive bad environment Bad: History of excessive bad environment |
- |
| Curr Com PCS-WIL-R | Driver seat active headrest ECU connection status | with or without | with: Driver seat active headrest ECU connected without: Driver seat active headrest ECU not connected |
Not Supported |
| Curr Com PCS-WIL-L | Front passenger seat active headrest ECU connection status | with or without | with: Front passenger seat active headrest ECU connected without: Front passenger seat active headrest ECU not connected |
Not Supported |
| Curr Com Night View ECU | Night view ECU connection status | with or without | with: Night view ECU connected without: Night view ECU not connected |
Not Supported |
| Curr Com Front Camera Module | Front camera module connection status | with or without | with: Front camera module connected without: Front camera module not connected |
Not Supported |
| Country# (DSS) | Destination country for driving support ECU assembly | JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX | Actual country code | - |
| The Number of DTCs | Number of DTCs | min: 0, max: 255 | Number of DTCs will be displayed | - |
Enter the following menus: Powertrain / Radar Cruise / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Country# (F Radar Sens) | Destination country for millimeter wave radar sensor assembly | JPN, NA, EURO, AUS, SAFC, OTHER, TWN, CHINA, THAI, GCC or NOFIX | Actual country code | - |
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Stop Light Relay Output | Stop light control relay (STOP LP) output | ON or OFF | ON: Relay output on (Stop light on) OFF: Relay output off (Stop light off) |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.
Perform Active Test according to the display on the GTS.
Tech Tips
The power switch must be turned on (IG) to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Radar Cruise Approach Alarm Buzzer | Skid control buzzer assembly | ON or OFF | Buzzer can be heard |
| PCS Crash Alarm Buzzer | Skid control buzzer assembly | ON or OFF | Buzzer can be heard |
| PCS Approach Alarm Buzzer | Skid control buzzer assembly | ON or OFF | Buzzer can be heard |
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Precrash | PCS warning indicator | ON or OFF | - |
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
Perform Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light control relay (STOP LP) | ON or OFF | Stop lights come on |