REAR SEAT SIDE AIRBAG ASSEMBLY DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Never dispose of a rear seat airbag assembly with an undeployed airbag.

    • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

    • When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform the operation in a place away from electrical noise.

    • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the rear seat airbag assembly.

    • The rear seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

    • Use gloves and safety glasses when handling a rear seat airbag assembly with a deployed airbag.

    • Do not apply water, etc. to a rear seat airbag assembly with a deployed airbag.

    • Always wash your hands with water after completing the operation.

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the rear seat airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

  2. DISPOSE OF REAR SEAT AIRBAG ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of a rear seat airbag assembly, never use the customer's vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a 12 V battery as the power source to deploy the airbag.


    1. A0022YCN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Refer to Precaution.

      Click here

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    4. Remove the rear seat cushion assembly.

      Click here

    5. Disconnect the rear seat airbag assembly connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. A00216SC14
        *a White Housing Lock
        *b Yellow CPA
        B003XUN Slide

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    6. Install SST.

      CAUTION:

      Check that there is no looseness in the rear side seatback assembly.


      1. A0022TLN01

        After connecting the following SST to each other, connect them to the rear seat airbag assembly.

        SST
        09082-00700
        09082-00820

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. A002223C05
        *a 12 V Battery
        *b 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the rear side window of the vehicle.

      3. Maintaining sufficient clearance for the SST wire harness in the rear side window, close all doors and windows of the vehicle.

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch to deploy the airbag.

        CAUTION:


        • Before deployment, make sure that no one is near the vehicle.

        • The rear seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling a rear seat airbag assembly with a deployed airbag.

        • Do not apply water, etc. to a rear seat airbag assembly with a deployed airbag.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

  3. DISPOSE OF REAR SEAT AIRBAG ASSEMBLY (When not Installed in Vehicle)

    Note


    • Be sure to observe the following procedure when deploying the airbag.

    • When disposing of a rear seat airbag assembly, perform the procedure with the rear seat airbag assembly installed to the rear side seatback assembly.

    Tech Tips

    Prepare a 12 V battery as the power source to deploy the airbag.


    1. A0022YCN08

      Check the function of SST.

      Click here

      SST
      09082-00700

    2. Remove the rear side seatback assembly.

      Click here

      CAUTION:


      • Before removing the rear side seatback assembly, wait at least 90 seconds after turning the power switch off and disconnecting the cable from the negative (-) auxiliary battery terminal.

      • When storing the rear side seatback assembly, keep the airbag deployment side facing upward.

    3. A0023APC16
      *a Wire Diameter
      *b Stripped Wire Cross Sectional Area

      Using braided wire, tie down the rear side seatback assembly to an unneeded tire.

      Wire
      Stripped wire cross sectional area
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the rear side seatback assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross sectional area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the cross sectional area of the stripped wire:

      Cross sectional area = 3.14 x (Diameter)2/ 4


      1. A0022KO

        Wind 2 or more wires around the stud bolts of the rear side seatback assembly as shown in the illustration.

      2. A00225OC01
        *a Width
        *b Inner Diameter

        Position the rear side seatback assembly inside the tire with the airbag deployment side facing inward.

        Minimum Tire Size
        Width
        185 mm (7.28 in.)
        Inner Diameter
        360 mm (1.18 ft.)

        CAUTION:


        • Make sure that the wires are tight. If there is slack in the wires, the rear side seatback assembly may break loose when the airbag is deployed.

        • Always tie down the rear side seatback assembly with the airbag deployment side facing inside the tire as shown in the illustration.

        Note

        The tire may be damaged by the airbag deployment, so use an unneeded tire.

    4. Install SST.


      1. A00216WN01

        Connect the SST connector to the rear seat airbag assembly connector.

        SST
        09082-00820

    5. Place the tires.


      1. A00239OC01
        *a Tires (2 or more)
        *b Inner Diameter
        *c Width

        Place at least 2 tires under the tire to which the rear side seatback assembly is tied.

        Minimum Tire Size
        Width
        185 mm (7.28 in.)
        Inner Diameter
        360 mm (1.18 ft.)

        Note

        Do not place the SST connector under the tire because it could be damaged.

      2. Place at least 2 tires onto the tire to which the rear side seatback assembly is tied. The top tire should have a wheel installed.

        Note

        The wheel and tires may be damaged by the airbag deployment, so use an unneeded wheel and tires.

      3. A0020N0

        Tie the tires together with 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.

    6. Install SST.


      1. A00223MC01
        *1 Rear Side Seatback Assembly
        *a 12 V Battery
        *b 10 m (32.8 ft.) or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the rear side seatback assembly is tied.

      3. Press the SST activation switch to deploy the airbag.

        CAUTION:

        Before deployment, make sure that no one is near the airbag.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the rear side seatback assembly.

      CAUTION:


      • The rear side seatback assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling a rear side seatback assembly with a deployed airbag.

      • Do not apply water, etc. to a rear side seatback assembly with a deployed airbag.

      • Always wash your hands with water after completing the operation.


      1. Remove the rear side seatback assembly from the tire.

      2. Place the rear side seatback assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.