SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof or Main Body / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Sliding Roof > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Open Switch OPEN switch signal OFF or ON

      OFF: OPEN switch not pressed

      ON: OPEN switch pressed

      		 -
      Close Switch CLOSE switch signal OFF or ON

      OFF: CLOSE switch not pressed

      ON: CLOSE switch pressed

      		 -
      Up Switch UP switch signal OFF or ON

      OFF: UP switch not pressed

      ON: UP switch pressed

      		 -
      Down Switch DOWN switch signal OFF or ON

      OFF: DOWN switch not pressed

      ON: DOWN switch pressed

      		 -
      Front SW Auto Operation Sliding roof auto function OFF or ON Customization status displayed -
      Hall IC1 Pulse Hall IC1 pulse output Lo or Hi Lo and Hi repeat during motor operation

      Lo: Hall IC1 output is low

      Hi: Hall IC1 output is high
      Hall IC1 Status Status of Hall IC1 Normal or Error

      Normal: Hall IC1 normal

      Error: Hall IC1 not normal

      		 -
      Hall IC2 Pulse Hall IC2 pulse output Lo or Hi Lo and Hi repeat during motor operation

      Lo: Hall IC2 output is low

      Hi: Hall IC2 output is high
      Hall IC2 Status Status of Hall IC2 Normal or Error

      Normal: Hall IC2 normal

      Error: Hall IC2 not normal

      		 -
      Ignition (Direct Signal) Power switch signal OFF or ON

      OFF: Power switch off

      ON: Power switch on (IG)

      		 -
      Ignition (MPX) Power switch signal (LIN signal) OFF or ON

      OFF: Power switch off

      ON: Power switch on (IG)

      		 -
      Door Courtesy Driver door courtesy light switch signal OFF or ON

      OFF: Driver door closed

      ON: Driver door open

      		 -
      Door Key Close Operation Key-linked sliding roof close signal OFF or ON

      OFF: Driver door key cylinder not turned

      ON: Driver door key cylinder turned and held at the lock position

      		 -
      Door Key Open Operation Key-linked sliding roof open signal OFF or ON

      OFF: Driver door key cylinder not turned

      ON: Driver door key cylinder turned and held at the unlock position

      		 -
      Wireless Close Operation Wireless transmitter-linked sliding roof close signal OFF or ON

      OFF: Transmitter LOCK switch not pressed

      ON: Transmitter LOCK switch pressed and held

      		 -
      Wireless Open Operation Wireless transmitter-linked sliding roof open signal OFF or ON

      OFF: Transmitter UNLOCK switch not pressed

      ON: Transmitter UNLOCK switch pressed and held

      		 -
      Key Off Permission Key-off sliding roof operation permit signal OFF or ON

      OFF: Any status except "ON" status

      ON: Front doors are not opened within 43 seconds after power switch turned off

      		 -
      Window Lock Window lock switch signal OFF or ON

      OFF: Window lock switch UNLOCK position

      ON: Window lock switch LOCK position

      		 -
      Door Key Related Operation Key-linked sliding roof open function operating direction Slide or Tilt Customization status displayed -
      Wireless Key Rel Operation Wireless transmitter-linked sliding roof open function operating direction Slide or Tilt Customization status displayed -
      Open Switch Failure(Past) Open switch failure signal (Past) OFF or ON

      OFF: No sliding roof open switch failure signal (Past)

      ON: Sliding roof open switch failure signal (Past)

      		 -
      Close Switch Failure(Past) Close switch failure signal (Past) OFF or ON

      OFF: No sliding roof close switch failure signal (Past)

      ON: Sliding roof close switch failure signal (Past)

      		 -
      Up Switch Failure(Past) Up switch failure signal (Past) OFF or ON

      OFF: No sliding roof tilt up switch failure signal (Past)

      ON: Sliding roof tilt up switch failure signal (Past)

      		 -
      Down Switch Failure(Past) Down switch failure signal (Past) OFF or ON

      OFF: No sliding roof tilt down switch failure signal (Past)

      ON: Sliding roof tilt down switch failure signal (Past)

      		 -
      Open Switch Failure(Current) Open switch failure signal (Current) OFF or ON

      OFF: No sliding roof open switch failure signal (Current)

      ON: Sliding roof open switch failure signal (Current)

      		 -
      Close Switch Failure(Current) Close switch failure signal (Current) OFF or ON

      OFF: No sliding roof close switch failure signal (Current)

      ON: Sliding roof close switch failure signal (Current)

      		 -
      Up Switch Failure(Current) Up switch failure signal (Current) OFF or ON

      OFF: No sliding roof tilt up switch failure signal (Current)

      ON: Sliding roof tilt up switch failure signal (Current)

      		 -
      Down Switch Failure(Current) Down switch failure signal (Current) OFF or ON

      OFF: No sliding roof tilt down switch failure signal (Current)

      ON: Sliding roof tilt down switch failure signal (Current)

      		 -
      Number of Trouble Codes Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -

      Body Electrical > Main Body > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      IG SW Power switch status OFF or ON

      OFF: Power switch off

      ON: Power switch on (IG)

      		 "OFF" is displayed even though the power switch is on (ACC).
      FR Door Courtesy SW Front door courtesy light switch assembly (for RH) signal OFF or ON

      OFF: Front door RH closed

      ON: Front door RH open

      		 -
      FL Door Courtesy SW Front door courtesy light switch assembly (for LH) signal OFF or ON

      OFF: Front door LH closed

      ON: Front door LH open

      		 -
      Door Key P/W Up Door key linked sliding roof close OFF or ON Customization status displayed -
      Door Key P/W Down Door key linked sliding roof open OFF or ON Customization status displayed -
      P/W Up W/ Transmit Wireless transmitter linked sliding roof close OFF or ON Customization status displayed -
      P/W Down W/ Transmit Wireless transmitter linked sliding roof open OFF or ON Customization status displayed -
      Slide Roof Open Warning Sliding roof open warning OFF or ON Customization status displayed -
      Communication Slide Roof Connection status between sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) STOP or OK

      STOP: Communication stopped

      OK: Normal communication

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Active Test.

    5. According to the display on the GTS, perform the Active Test.


      Body Electrical > Sliding Roof > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Slide Roof Operate sliding roof motor OFF / Opn/Dwn / Clos/Up -