PUSH-BUTTON START, Diagnostic DTC:U0100, U0140, U0142, U0155, U1103, U1117

DTC Code DTC Name
U0100 Lost Communication with ECM / PCM
U0140 Lost Communication with Main Body ECU
U0142 Lost Communication with Main Body ECU
U0155 Lost Communication with Combination Meter
U1103 Lost Communication with Stop and Start Control Module
U1117 Lost Communication with Accessory Gateway

DESCRIPTION

These DTCs are stored when there is a CAN communication error between the certification ECU (smart key ECU assembly), ECM, main body ECU (multiplex network body ECU) or combination meter assembly, and data from the option connector (bus buffer ECU) cannot be received.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0100 Lost Communication with ECM / PCM CAN communication error between certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*) ECM

    DTC Output Confirmation Operation:

  • Turn the engine switch on (IG) and wait 10 seconds or more.
U0140 Lost Communication with Main Body ECU CAN communication error between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) Main body ECU (multiplex network body ECU)

    DTC Output Confirmation Operation:

  • Always
U0142 Lost Communication with Main Body ECU CAN communication error between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) Main body ECU (multiplex network body ECU)

    DTC Output Confirmation Operation:

  • Always
U0155 Lost Communication with Combination Meter CAN communication error between certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*) Combination meter assembly

    DTC Output Confirmation Operation:

  • Turn the engine switch on (IG) and wait 10 seconds or more.
U1103 Lost Communication with Stop and Start Control Module CAN communication error between the certification ECU (smart key ECU assembly) and engine stop and start ECU (1-trip detection*) Engine stop and start ECU

    DTC Output Confirmation Operation:

  • Turn the engine switch on (IG) and wait 10 seconds or more.
U1117 Lost Communication with Accessory Gateway Data from the option connector (bus buffer ECU) cannot be received.

  • Connector and branch wire of sub bus 2 of option connector (bus buffer ECU)

  • Internal malfunction of option connector (bus buffer ECU)

    DTC Output Confirmation Operation:

  • Turn the engine switch on (IG) and wait 10 seconds or more.

Vehicle Condition and Fail-safe Function when Malfunction Detected
DTC Code Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
U0100 There is no effect on vehicle behavior.

If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in CAN communication.


  • When the engine switch is pressed, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

  • When the engine switch is pressed and held, the system controls the engine based on the engine speed signal via direct line, causing the engine to stop cranking.

If the following conditions are met, it can be determined that there is a malfunction in both CAN communication and the direct line (NE).


  • When the engine switch is pressed, the engine stops cranking after 6 seconds.

  • When the engine switch is pressed and held, the engine remains cranking for up to 30 seconds.

U0140

U0142

  • Doors cannot be locked or unlocked.

  • The warning (wireless buzzer) does not sound.

 -
U0155 The warning (meter buzzer) does not sound and the meter does not indicate a warning. -
U1103*

  • When idling is stopped by the stop and start system, the ECM misjudges it as an engine stall.

  • While the engine is stopped by the stop and start system, the immobiliser system is set due to a door operation.

 -
U1117 The engine cannot be started using the wireless remote control function. -

Related Data List and Active Test Items
DTC No. Data List and Active Test

U0100

U0140

U0142

U0155

U1103*

U1117

 -

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

Tech Tips

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

PROCEDURE


  1. CHECK FOR DTC


    1. Note any DTCs that are output.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here