NAVIGATION SYSTEM Speaker Circuit

DESCRIPTION

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver*1 or speakers.

*1: w/ Telematics Transceiver

WIRING DIAGRAM


  1. for 8 Speakers

    A001KG8E05
    A001IAVE05

  2. for 15 Speakers

    A001I45E05
    A001JQ7E03

CAUTION / NOTICE / HINT

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click here

PROCEDURE


  1. CONFIRM MODEL


    1. Choose the model to be inspected.

      Result
      Result Proceed to
      for 8 Speakers A
      for 15 Speakers B

    B

    CHECK SPEAKER (OPERATION CHECK) Click here

    A

  2. CHECK SPEAKER (OPERATION CHECK)


    1. B003TTP

      Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly (w/ Telematics Transceiver) A
      Front No. 2 speaker assembly (w/o Telematics Transceiver) B
      Front No. 1 speaker assembly C
      Rear speaker assembly D
      Rear No. 3 speaker assembly E
      Front No. 3 speaker assembly F

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K66 telematics transceiver connector.

    3. Disconnect the K55 and K56 front No. 2 speaker assembly connectors.

    4. Measure the resistance between the stereo component amplifier assembly and the telematics transceiver to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - K66-2 (SPI+) Always Below 1 Ω
      P23-28 (FR-) - K66-3 (SPI-) Always Below 1 Ω

    5. Measure the resistance between the front No. 2 speaker assembly RH and the telematics transceiver to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K66-5 (SPO+) - K55-2 (+) Always Below 1 Ω
      K66-6 (SPO-) - K55-1 (-) Always Below 1 Ω

    6. Measure the resistance between the front No. 2 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-12 (FL+) - K56-2 (+) Always Below 1 Ω
      P23-27 (FL-) - K56-1 (-) Always Below 1 Ω

    7. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - Body ground Always 10 kΩ or higher
      P23-28 (FR-) - Body ground Always 10 kΩ or higher
      P23-12 (FL+) - Body ground Always 10 kΩ or higher
      P23-27 (FL-) - Body ground Always 10 kΩ or higher

    8. Measure the resistance between the front No. 2 speaker assembly RH and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K55-2 (+) - Body ground Always 10 kΩ or higher
      K55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. A001IJVC23
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 18 Click here

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K55 and K56 front No. 2 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - K55-2 (+) Always Below 1 Ω
      P23-28 (FR-) - K55-1 (-) Always Below 1 Ω
      P23-12 (FL+) - K56-2 (+) Always Below 1 Ω
      P23-27 (FL-) - K56-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - Body ground Always 10 kΩ or higher
      P23-28 (FR-) - Body ground Always 10 kΩ or higher
      P23-12 (FL+) - Body ground Always 10 kΩ or higher
      P23-27 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly.

      Click here

    2. A001IJVC23
      *a

      Component without harness connected

      (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

  7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the N14 and N29 front No. 1 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-5 (WFR+) - N14-1 Always Below 1 Ω
      P23-20 (WFR-) - N14-2 Always Below 1 Ω
      P23-4 (WFL+) - N29-1 Always Below 1 Ω
      P23-19 (WFL-) - N29-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-5 (WFR+) - Body ground Always 10 kΩ or higher
      P23-20 (WFR-) - Body ground Always 10 kΩ or higher
      P23-4 (WFL+) - Body ground Always 10 kΩ or higher
      P23-19 (WFL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B003X4IC04
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  9. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the O4 and O9 rear speaker assembly connectors.

    3. Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-15 (RR+) - O4-1 Always Below 1 Ω
      P23-30 (RR-) - O4-2 Always Below 1 Ω
      P23-14 (RL+) - O9-1 Always Below 1 Ω
      P23-29 (RL-) - O9-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-15 (RR+) - Body ground Always 10 kΩ or higher
      P23-30 (RR-) - Body ground Always 10 kΩ or higher
      P23-14 (RL+) - Body ground Always 10 kΩ or higher
      P23-29 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. B003X4IC03
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.2 to 4.8 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  11. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the P27 rear No. 3 speaker assembly connector.

    3. Measure the resistance between the rear No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-6 (WF1+) - P27-1 Always Below 1 Ω
      P23-21 (WF1-) - P27-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-6 (WF1+) - Body ground Always 10 kΩ or higher
      P23-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. B003X4IC03
      *a

      Component without harness connected

      (Rear No. 3 Speaker Assembly )

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 2.0 to 3.0 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here

  13. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K57 front No. 3 speaker assembly connector.

    3. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-7 (CTR+) - K57-2 (+) Always Below 1 Ω
      P23-22 (CTR-) - K57-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-7 (CTR+) - Body ground Always 10 kΩ or higher
      P23-22 (CTR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly.

      Click here

    2. A001IJVC23
      *a

      Component without harness connected

      (Front No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (-) - 2 (+) Always 4.0 to 6.0 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

  15. CHECK SPEAKER (OPERATION CHECK)


    1. B003TTP

      Enter the "System Check Mode" screen. Refer to Check SP Check On in Operation Check.

      Click here

    2. Perform the operation check above and determine the speaker that is not operating.

      Result
      Not Operating Speaker Proceed to
      Front No. 2 speaker assembly (w/ Telematics Transceiver) A
      Front No. 2 speaker assembly (w/o Telematics Transceiver) B
      Front No. 1 speaker assembly C
      Front No. 3 speaker assembly D
      Rear speaker assembly or rear No. 2 speaker assembly E
      Rear header speaker assembly F
      Rear No. 3 speaker assembly G

      Tech Tips

      If sound cannot be heard from any speaker, inspect all of them.


    B

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) Click here

    C

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) Click here

    D

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) Click here

    E

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) Click here

    F

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY) Click here

    G

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY) Click here

    A

  16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K66 telematics transceiver connector.

    3. Disconnect the K55 and K56 front No. 2 speaker assembly connectors.

    4. Measure the resistance between the stereo component amplifier assembly and the telematics transceiver to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - K66-2 (SPI+) Always Below 1 Ω
      P23-28 (FR-) - K66-3 (SPI-) Always Below 1 Ω

    5. Measure the resistance between the front No. 2 speaker assembly RH and the telematics transceiver to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K66-5 (SPO+) - K55-2 (+) Always Below 1 Ω
      K66-6 (SPO-) - K55-1 (-) Always Below 1 Ω

    6. Measure the resistance between the front No. 2 speaker assembly LH and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-12 (FL+) - K56-2 (+) Always Below 1 Ω
      P23-27 (FL-) - K56-1 (-) Always Below 1 Ω

    7. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - Body ground Always 10 kΩ or higher
      P23-28 (FR-) - Body ground Always 10 kΩ or higher
      P23-12 (FL+) - Body ground Always 10 kΩ or higher
      P23-27 (FL-) - Body ground Always 10 kΩ or higher

    8. Measure the resistance between the front No. 2 speaker assembly RH and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K55-2 (+) - Body ground Always 10 kΩ or higher
      K55-1 (-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  18. INSPECT TELEMATICS TRANSCEIVER


    1. Remove the telematics transceiver.

      Click here

    2. A001JQLC05
      *a

      Component without harness connected

      (Telematics Transceiver)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 5 (SPO+) Always Below 1 Ω
      3 (SPI-) - 6 (SPO-) Always Below 1 Ω
      2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
      5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE TELEMATICS TRANSCEIVER Click here

  19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K55 and K56 front No. 2 speaker assembly connectors.

    3. Measure the resistance between the stereo component amplifier assembly and each of the front No. 2 speaker assemblies to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - K55-2 (+) Always Below 1 Ω
      P23-28 (FR-) - K55-1 (-) Always Below 1 Ω
      P23-12 (FL+) - K56-2 (+) Always Below 1 Ω
      P23-27 (FL-) - K56-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-13 (FR+) - Body ground Always 10 kΩ or higher
      P23-28 (FR-) - Body ground Always 10 kΩ or higher
      P23-12 (FL+) - Body ground Always 10 kΩ or higher
      P23-27 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  21. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the N14 and N29 front No. 1 speaker assembly connectors.

    3. Measure the resistance between each of the front No. 1 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-5 (WFR+) - N14-1 Always Below 1 Ω
      P23-20 (WFR-) - N14-2 Always Below 1 Ω
      P23-4 (WFL+) - N29-1 Always Below 1 Ω
      P23-19 (WFL-) - N29-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-5 (WFR+) - Body ground Always 10 kΩ or higher
      P23-20 (WFR-) - Body ground Always 10 kΩ or higher
      P23-4 (WFL+) - Body ground Always 10 kΩ or higher
      P23-19 (WFL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  22. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly.

      Click here

    2. B003X4IC03
      *a

      Component without harness connected

      (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 4.3 to 6.3 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

  23. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the K57 front No. 3 speaker assembly connector.

    3. Measure the resistance between the front No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-7 (CTR+) - K57-2 (+) Always Below 1 Ω
      P23-22 (CTR-) - K57-1 (-) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-7 (CTR+) - Body ground Always 10 kΩ or higher
      P23-22 (CTR-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  24. REPLACE FRONT NO. 3 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips

      Connect the connector to the front No. 3 speaker assembly that was disconnected.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  25. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the O5 and O10 rear No. 2 speaker assembly connectors.

    3. Measure the resistance between each of the rear No. 2 speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-15 (RR+) - O5-3 (+TW) Always Below 1 Ω
      P23-30 (RR-) - O5-1 (-TW) Always Below 1 Ω
      P23-14 (RL+) - O10-3 (+TW) Always Below 1 Ω
      P23-29 (RL-) - O10-1 (-TW) Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-15 (RR+) - Body ground Always 10 kΩ or higher
      P23-30 (RR-) - Body ground Always 10 kΩ or higher
      P23-14 (RL+) - Body ground Always 10 kΩ or higher
      P23-29 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  26. CHECK HARNESS AND CONNECTOR (REAR SPEAKER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY)


    1. Disconnect the O4 and O9 rear speaker assembly connectors.

    2. Disconnect the O5 and O10 rear No. 2 speaker assembly connectors.

    3. Measure the resistance between each of the rear speaker assemblies and the rear No. 2 speaker assemblies to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-1 - O5-4 (+) Always Below 1 Ω
      O4-2 - O5-2 (-) Always Below 1 Ω
      O9-1 - O10-4 (+) Always Below 1 Ω
      O9-2 - O10-2 (-) Always Below 1 Ω

    4. Measure the resistance between each of the rear speaker assemblies and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O4-1 - Body ground Always 10 kΩ or higher
      O4-2 - Body ground Always 10 kΩ or higher
      O9-1 - Body ground Always 10 kΩ or higher
      O9-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  27. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.

      Click here

    2. A001HN3C21
      *a

      Component without harness connected

      (Rear No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (+TW) - 1 (-TW) Always 10 kΩ or higher
      3 (+TW) - 4 (+) Always Below 1 Ω
      1 (-TW) - 2 (-) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    OK

  28. REPLACE REAR NO. 2 SPEAKER ASSEMBLY


    1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK
      Malfunction disappears.

      Tech Tips


      • Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left rear No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  29. INSPECT REAR SPEAKER ASSEMBLY


    1. Remove the rear speaker assembly.

      Click here

    2. B003X4IC03
      *a

      Component without harness connected

      (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 3.6 to 5.6 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY Click here

  30. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR HEADER SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the P26 and Q40 rear header speaker assembly connectors.

    3. Measure the resistance between each of the rear header speaker assemblies and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-11 (SR+) - P26-2 Always Below 1 Ω
      P23-26 (SR-) - P26-1 Always Below 1 Ω
      P23-10 (SL+) - Q40-2 Always Below 1 Ω
      P23-25 (SL-) - Q40-1 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-11 (SR+) - Body ground Always 10 kΩ or higher
      P23-26 (SR-) - Body ground Always 10 kΩ or higher
      P23-10 (SL+) - Body ground Always 10 kΩ or higher
      P23-25 (SL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  31. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly.

      Click here

    2. A001JFEC01
      *a

      Component without harness connected

      (Rear Header Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 7.0 to 10.6 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

  32. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 3 SPEAKER ASSEMBLY)


    1. Disconnect the P23 stereo component amplifier assembly connector.

    2. Disconnect the P27 rear No. 3 speaker assembly connector.

    3. Measure the resistance between the rear No. 3 speaker assembly and the stereo component amplifier assembly to check for an open circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-6 (WF1+) - P27-1 Always Below 1 Ω
      P23-21 (WF1-) - P27-2 Always Below 1 Ω

    4. Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P23-6 (WF1+) - Body ground Always 10 kΩ or higher
      P23-21 (WF1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  33. INSPECT REAR NO. 3 SPEAKER ASSEMBLY


    1. Remove the rear No. 3 speaker assembly.

      Click here

    2. B003X4IC03
      *a

      Component without harness connected

      (Rear No. 3 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 5.0 to 7.0 Ω
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

    REPLACE REAR NO. 3 SPEAKER ASSEMBLY Click here