ROOF HEADLINING REASSEMBLY

PROCEDURE


  1. INSTALL NO. 1 ROOF WIRE


    1. w/o Pre-collision System (When using a new roof headlining):

      A001LDXC01
      *A for RHD with Rain Sensor *B w/ EC Mirror
      *C for LHD with Rain Sensor - -
      *a Marking *b Cut

      1. Using a knife, cut the roof headlining at the markings as shown in the illustration.

        Tech Tips

        Make sure to cut the roof headlining at the same positions as the removed roof headlining.

    2. w/ Pre-collision System (When using a new roof headlining):

      A001IVXC02
      *A for RHD with Rain Sensor *B w/ EC Mirror
      *C for LHD with Rain Sensor - -
      *a Marking *b Cut

      1. Using a knife, cut the roof headlining at the markings as shown in the illustration.

        Tech Tips

        Make sure to cut the roof headlining at the same positions as the removed roof headlining.

    3. Apply butyl tape as shown in the illustration.

      A001J0LC02
      *A w/o Sliding Roof *B w/ Sliding Roof
      *a Marking - -
      B003V9P Butyl Tape - -

      Note

      Securely attach butyl tape.

    4. Engage the 6 clamps (A).

      A001ICTC01
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/o Pre-collision System *D w/ Pre-collision System
      *E for LHD with Rain Sensor *F for RHD with Rain Sensor
      *G w/ EC Mirror - -
      *a Clamp (A) *b Clamp (B)
      *c Marking Tape (A) *d Marking Tape (B)
      *e Marking Tape (C) *f Marking Tape (D)
      *g Adjustment Area *h 90°

    5. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    6. Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining.

    7. Align the edge of the marking tape (B) on the No. 1 roof wire with the markings on the roof headlining.

    8. Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining.

    9. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    10. w/ Sliding Roof:


      1. Engage the 5 clamps (B).

    11. Align the edge of each marking tape (D) on the No. 1 roof wire with each notch on the roof headlining.

    12. Install the No. 1 roof wire to the roof headlining with adhesive tape.

      A001J6RC01
      *A w/o Sliding Roof *B w/ Sliding Roof
      *C w/o Pre-collision System *D w/ Pre-collision System
      *E for LHD with Rain Sensor *F for RHD with Rain Sensor
      *G w/ EC Mirror - -
      *a Correct *b Incorrect
      *c Marking *d 15 mm (0.591 in.) or more
      B003V9P Adhesive Tape - -

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  2. INSTALL REAR SIDE RAIL SPACER LH (w/o Sliding Roof)


    1. A001IJUC01
      *a Marking

      Align the rear side rail spacer LH with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      Tech Tips

      Install the rear side rail spacer LH with the arrow on the spacer facing the front of the vehicle.

  3. INSTALL REAR SIDE RAIL SPACER LH (w/ Sliding Roof)


    1. A001I71C01
      *a Marking

      Align the rear side rail spacer LH with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

      Tech Tips

      Install the rear side rail spacer LH with the arrow on the spacer facing the front of the vehicle.

  4. INSTALL REAR SIDE RAIL SPACER RH (w/o Sliding Roof)

    Tech Tips

    Use the same procedure as for the LH side.

  5. INSTALL REAR SIDE RAIL SPACER RH (w/ Sliding Roof)

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Align the 2 No. 3 roof silencer pads with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

      A001I2JC02
      *a Marking - -

  7. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)


    1. A001JUGC02
      *a Marking

      Align the No. 2 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

  8. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)


    1. A001IODC02
      *a Marking

      Align the No. 1 roof silencer pad with the markings on the roof headlining assembly and install it using hot-melt glue as shown in the illustration.

  9. INSTALL ROOF HEADLINING PAD (w/o Sliding Roof)


    1. A001KV4C02
      *a Marking

      Align the 2 roof headlining pads with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

  10. INSTALL ROOF HEADLINING PAD (w/ Sliding Roof)


    1. A001LEMC03
      *a Marking

      Align the 2 roof headlining pads with the markings on the roof headlining assembly and install them using hot-melt glue as shown in the illustration.

  11. INSTALL VANITY LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure for the LH side and RH side.


    1. A001KVFC02
      *1 Bulb Holder

      Engage the claw (B) to temporarily install the vanity light assembly.

    2. Engage the 2 claws (A) to install the bulb holder to the vanity light assembly.