PARKING BRAKE PEDAL(for RHD) REMOVAL

PROCEDURE


  1. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure as for LHD.

    for Manual Seat: Click here

    for Power Seat: Click here

  3. REMOVE YAWRATE SENSOR BRACKET

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  4. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  5. REMOVE AIR DUCT SUB-ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  6. REMOVE ACCELERATOR PEDAL PAD

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  7. REMOVE ACCELERATOR PEDAL ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  8. REMOVE FLOOR CARPET HOOK


    1. B003U3I

      Disengage the 2 clamps and disconnect the wire harness.

    2. B003X0G

      Disengage the 2 clamps to remove the 2 floor carpet hooks.

  9. REMOVE REAR NO. 4 AIR DUCT

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  10. REMOVE FRONT FLOOR SILENCER PAD RH

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  11. REMOVE REAR NO. 3 AIR DUCT

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  12. REMOVE NO. 2 DASH PANEL INSULATOR PAD


    1. B003WM8

      Disengage the 2 clips to remove the No. 2 dash panel insulator pad.

  13. REMOVE AIRBAG SENSOR ASSEMBLY

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  14. REMOVE FRONT FLOOR REAR UPPER SUB PANEL SUB-ASSEMBLY


    1. B003WB1

      Disengage the 6 clamps from the front upper floor rear sub panel sub-assembly.

    2. B003WSP

      Disengage the 2 guides from the front floor mat.

    3. Remove the 4 bolts.

    4. B003T2U

      Disengage the clamp, and remove the front upper floor rear sub panel sub-assembly.

  15. LOOSEN NO. 1 WIRE ADJUSTING NUT


    1. Completely release the parking brake pedal.

    2. B003WP6C01
      *1 No. 1 Wire Adjusting Nut
      *2 Lock Nut

      Loosen the lock nut and the No. 1 wire adjusting nut to completely release the parking brake cable.

  16. REMOVE PARKING BRAKE RETURN WITH DAMPER SPRING


    1. B003U2U

      Using needle-nose pliers, remove the parking brake return with damper spring.

  17. REMOVE PARKING BRAKE EQUALIZER


    1. B003T1NC01
      *1 No. 2 Parking Brake Cable Assembly
      *2 No. 3 Parking Brake Cable Assembly

      Remove the 2 nuts and separate the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly from the parking brake equalizer.

    2. B003UJY

      Slide the rubber boot as shown in the illustration.

    3. B003VLRN01

      Remove the parking brake equalizer as shown in the illustration.

  18. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY


    1. B003X6N

      Remove the 2 nuts, and separate the No. 1 parking brake cable assembly from the body.

    2. B003UT6

      Remove the 2 bolts, and separate the No. 1 parking brake cable assembly from the body.

    3. B003VQM

      Disconnect the parking brake switch connector.

    4. B003SU2

      Remove the bolt, 2 nuts and parking brake control pedal assembly from the body.