AUTOMATIC TRANSMISSION SYSTEM(for 2GR-FSE), Diagnostic DTC:P2716

DTC Code DTC Name
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

DESCRIPTION

Refer to DTC P2714.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)

  1. Diagnosis Condition


    • Engine is running

  2. Malfunction Status


    • Shift solenoid valve SLT circuit is open or shorted

  3. Malfunction Time


    • 1 second

  4. Other


    • 1 trip detection logic

  • Shift solenoid valve SLT

  • Transmission wire

  • Harness and connector

  • TCM

 Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the TCM determines that there is a malfunction.

The TCM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

B003WX7E11
*a Shift Solenoid Valve SLT
*b Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT) - TCM)


    1. B003T6PC16
      *a

      Rear view of wire harness connector

      (to TCM)

      Disconnect the F71 TCM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F71-1 (SLT+) - F71-7 (SLT-) Always 5.0 to 5.6 Ω
      F71-1 (SLT+) or F71-7 (SLT-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) Click here

    OK

  2. REPLACE TCM


    1. Replace the TCM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)


    1. Disconnect the F73 transmission wire connector.

    2. Disconnect the F71 TCM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F73-3 (SLT+) - F71-1 (SLT+) Always Below 1 Ω
      F73-4 (SLT-) - F71-7 (SLT-) Always Below 1 Ω
      F73-3 (SLT+) or F71-1 (SLT+) - Body ground Always 10 kΩ or higher
      F73-4 (SLT-) or F71-7 (SLT-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT SHIFT SOLENOID VALVE SLT


    1. B003VU8C46
      *a

      Component without harness connected

      (Shift Solenoid Valve SLT)

      Remove the shift solenoid valve SLT.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SLT - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a battery positive (+) lead with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE SHIFT SOLENOID VALVE SLT Click here