AUTOMATIC TRANSMISSION SYSTEM(for 8AR-FTS), Diagnostic DTC:P276512, P276514, P276531

DTC Code DTC Name
P276512 Input/Turbine Speed Sensor "B" Circuit Short to Battery
P276514 Input/Turbine Speed Sensor "B" Circuit Short to Ground or Open
P276531 Input/Turbine Speed Sensor "B" No Signal

DESCRIPTION

The transmission revolution sensor (NC3) detects the automatic transmission No. 3 clutch drum rotation speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P276512 Input/Turbine Speed Sensor "B" Circuit Short to Battery

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. The battery voltage is 8 V or more, the engine switch is on (IG) and the starter is off.

  2. Transmission revolution sensor (NC3) output voltage is more than 1.9 V

  3. 4.5 seconds

  4. 1-trip detection logic

  • Transmission revolution sensor (NC3)

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P07C2
P276514 Input/Turbine Speed Sensor "B" Circuit Short to Ground or Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. The battery voltage is 8 V or more, the engine switch is on (IG) and the starter is off.

  2. Transmission revolution sensor (NC3) output voltage is less than 0.1 V

  3. 4.5 seconds

  4. 1-trip detection logic

  • Transmission revolution sensor (NC3)

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P07C1
P276531 Input/Turbine Speed Sensor "B" No Signal

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. All conditions are met:


    1. The battery voltage is 8 V or more.

    2. Park/neutral position switch D input signal is ON.

    3. Transmission revolution sensor (SP2) value is 30 km/h (19 mph) or more.

    4. Transmission revolution sensor (NT) value is 740 rpm or more.

  2. Transmission revolution sensor (NC3) value is less than 300 rpm

  3. 5 seconds

  4. 1-trip detection logic

  • Transmission revolution sensor (NC3)

  • Transmission wire

  • Harness and connector

  • ECM

 Comes on DTC stored

SAE Code:

P2767

MONITOR DESCRIPTION

The NC3 terminal of the ECM detects a pulse signal from the transmission revolution sensor (NC3) (input RPM). The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensor (NC3 and SP2).

While the vehicle is being driven in 3rd, 4th, 5th, 6th or 7th gear with the shift lever in D, if the No. 3 clutch drum speed is less than 300 rpm* when the output shaft speed is 30 km/h (19 mph) or more, the ECM determines that there is a malfunction, illuminates the MIL and stores a DTC.

*: Pulse is not output or is irregularly output.

WIRING DIAGRAM

A001KU8E37
*a Transmission Revolution Sensor (NC3)
*b Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Perform the D Position Shift Test inspection in Road Test.

    Click here

  2. Check for DTCs again.

    Click here


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Data List / NC3 Sensor Speed.

    7. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      NC3 Sensor Speed No. 3 clutch drum speed

      Min.: 0 rpm

      Max.: 12750 rpm

      • 0 rpm: 2nd or 8th gear

      • Above 0 rpm: 1st, or 3rd to 7th gear

      		 Data is displayed in increments of 50 rpm

      Powertrain > Transmission > Data List
      Tester Display
      NC3 Sensor Speed

      Tech Tips


      • NC3 Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

      • NC3 Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction of the circuit.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Transmission / Data List / NC3 Sensor voltage, NC3 Sensor Speed.

    5. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      NC3 Sensor Voltage NC3 Sensor Voltage

      Min.: 0.000 V

      Max.: 4.999 V

      		 0.1 to 1.9 V: Idling -
      NC3 Sensor Speed No. 3 clutch drum speed

      Min.: 0 rpm

      Max.: 12750 rpm

      • 0 rpm: 2nd or 8th gear

      • Above 0 rpm: 1st, or 3rd to 7th gear

      		 Data is displayed in increments of 50 rpm

      Powertrain > Transmission > Data List
      Tester Display
      NC3 Sensor Voltage
      NC3 Sensor Speed
      Result
      Result Proceed to
      Data List value is normal A
      Data List value is not normal B

    A

    GO TO STEP 5 Click here

    B

  2. CHECK TRANSMISSION REVOLUTION SENSOR TERMINAL (NC3 TERMINAL)


    1. B003UDYC28
      *a

      Front view of wire harness connector

      (to Transmission Wire)

      Disconnect the F73 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F73-19 (NC3O) - Body ground Always 99 to 101 Ω

    3. Turn the engine switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F73-18 (NC3B) - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  3. INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC3))


    1. A001HYBC04
      *a

      Front view of wire harness connector

      (to Transmission Revolution Sensor (NC3))
      *b

      Component without harness connected

      (Transmission Wire)

      Disconnect the transmission revolution sensor (NC3) connector.

      Click here

    2. Disconnect the F73 transmission wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the transmission revolution sensor (NC3) connector - 18 (NC3B) Always Below 1 Ω
      Terminal 2 of the transmission revolution sensor (NC3) connector - 19 (NC3O) Always Below 1 Ω
      Terminal 1 of the transmission revolution sensor (NC3) connector or 18 (NC3B) - Body ground Always 10 kΩ or higher
      Terminal 2 of the transmission revolution sensor (NC3) connector or 19 (NC3O) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TRANSMISSION REVOLUTION SENSOR (NC3) Click here

    NG

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

  4. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the F73 transmission wire connector.

    2. Disconnect the F78 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F73-18 (NC3B) - F78-73 (NC3B) Always Below 1 Ω
      F73-19 (NC3O) - F78-74 (NC3O) Always Below 1 Ω
      F73-18 (NC3B) or F78-73 (NC3B) - Body ground Always 10 kΩ or higher
      F73-19 (NC3O) or F78-74 (NC3O) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here