COMBINATION SWITCH INSPECTION

PROCEDURE


  1. INSPECT COMBINATION SWITCH ASSEMBLY


    1. Inspect ECO mode switch:


      1. A001K09C15
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        11 (ECO) - 16 (E) Combination switch assembly knob turned and held at ECO position Below 50 Ω
        Combination switch assembly knob not turned to ECO position 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    2. Inspect NORMAL mode switch (w/o AVS):


      1. A001K09C16
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        9 (NORM) - 16 (E) Combination switch assembly knob pushed and held Below 50 Ω
        Combination switch assembly knob not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    3. Inspect NORMAL or CUSTOMIZE mode switch (w/ AVS):


      1. A001K09C16
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        9 (NORM) - 16 (E) Combination switch assembly knob pushed and held Below 50 Ω
        Combination switch assembly knob not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    4. Inspect SPORT or SPORT S/S+ mode switch:


      1. A001K09C17
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        10 (PWR) - 16 (E) Combination switch assembly knob turned and held at SPORT or SPORT S/S+ position Below 50 Ω
        Combination switch assembly knob not turned to SPORT or SPORT S/S+ position 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    5. Inspect SNOW mode switch:


      1. A001K09C18
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        3 (SNSW) - 16 (E) SNOW mode switch pushed and held Below 50 Ω
        SNOW mode switch not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    6. Inspect VSC off switch:


      1. A001K09C19
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1 (+) - 16 (E) VSC OFF mode switch pushed and held Below 50 Ω
        VSC OFF mode switch not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    7. Inspect Stop and Start System cancel switch:


      1. A001K09C14
        *a

        Component without harness connected

        (Combination Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2 (S) - 16 (E) Stop and Start System cancel switch pushed and held Below 50 Ω
        Stop and Start System cancel switch not pushed 10 kΩ or higher

        If the result is not as specified, replace the combination switch assembly.

    8. Inspect illumination:


      1. A001HHLC01
        *A w/o Stop and Start System Cancel Switch
        *B w/ Stop and Start System Cancel Switch
        *a

        Component without harness connected

        (Combination Switch Assembly)
        *b Combination Switch Assembly Illumination

        Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.

        Standard
        Measurement Condition Specified Condition

        Battery positive (+) → 5 (ILL+)

        Battery negative (-) → 8 (ILL-)

        		 Illuminates

        If the result is not as specified, replace the combination switch assembly.