COMBINATION SWITCH INSPECTION

PROCEDURE

1. INSPECT COMBINATION SWITCH ASSEMBLY

   
   

   1. Inspect ECO mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 11 (ECO) - 16 (E) ECO mode switch turned and held at ECO position Below 50 Ω ECO mode switch not turned 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   2. Inspect NORMAL mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 9 (NORM) - 16 (E) NORMAL mode switch pushed and held Below 50 Ω NORMAL mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   3. Inspect SPORT or SPORT S/S+ mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 10 (PWR) - 16 (E) SPORT or SPORT S/S+ mode switch turned and held at SPORT or SPORT S/S+ position Below 50 Ω SPORT or SPORT S/S+ mode switch not turned 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   4. Inspect SNOW mode switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 3 (SNSW) - 16 (E) SNOW mode switch pushed and held Below 50 Ω SNOW mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   5. Inspect VSC off switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 1 (+) - 16 (E) VSC OFF mode switch pushed and held Below 50 Ω VSC OFF mode switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   6. Inspect Stop and Start System cancel switch:

      
      
      1. 

         *a	Component without harness connected (Combination Switch Assembly)

         Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Condition Specified Condition 2 (S) - 16 (E) Stop and Start System cancel switch pushed and held Below 50 Ω Stop and Start System cancel switch not pushed 10 kΩ or higher

         If the result is not as specified, replace the combination switch assembly.

   7. Inspect illumination:

      
      
      1. 

         *A	w/o Stop and Start System Cancel Switch
         *B	w/ Stop and Start System Cancel Switch
         *a	Component without harness connected (Combination Switch Assembly)
         *b	Combination Switch Assembly Illumination

         Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.

         Standard
         Measurement Condition Specified Condition Battery positive (+) → 5 (ILL+) Battery negative (-) → 8 (ILL-) Illuminates

         If the result is not as specified, replace the combination switch assembly.