VALVE BODY ASSEMBLY(for 8AR-FTS) INSTALLATION

PROCEDURE


  1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. B003W06C01
      *1 Manual Valve Connecting Rod
      *2 Manual Valve Lever Sub-assembly

      Install the transmission valve body assembly and connect the manual valve connecting rod to the manual valve lever sub-assembly.

    2. B003TG3N01

      Install the 18 bolts to the transmission valve body assembly.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }
      Bolt Length
      Item Length
      Bolt A 31 mm (1.22 in.)
      Bolt B 21 mm (0.827 in.)

    3. Install the detent spring and detent spring cover with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. w/ Stop and Start System:


      1. Connect the 10 connectors.

      2. Coat the O-ring with ATF.

      3. Connect the ATF temperature sensor and install the lock plate with the bolt.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Note


        • When reusing the ATF temperature sensor, inspect the O-ring.

        • Make sure that the O-ring is not cracked or jammed when installing the transmission wire.

    5. w/o Stop and Start System:


      1. Connect the 9 connectors.

      2. Coat the O-ring with ATF.

      3. Connect the ATF temperature sensor and install the lock plate with the bolt.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Note


        • When reusing the ATF temperature sensor, inspect the O-ring.

        • Make sure that the O-ring is not cracked or jammed when installing the transmission wire.

  2. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    1. Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

      Note

      Ensure that the O-ring is not twisted or pinched.

    2. Install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. B003WPEC02
      *1 Transmission Oil Cleaner Magnet

      Install the 3 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.

    2. Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.

    3. B003WNI

      Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 9 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note

      B003UVYC09
      *1 Automatic Transmission Case Sub-assembly
      *2 Sleeve
      *a Correct
      *b Incorrect
      *c Protrusion

      • Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.

      • Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.

      • Make sure that the 9 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.

      • When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between a sleeve and the seal surface of the automatic transmission case sub-assembly.

  4. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  5. INSTALL FRONT SUSPENSION MEMBER BRACE

    Click here

  6. ADD AUTOMATIC TRANSMISSION FLUID

    Click here

  7. RESET MEMORY

    Click here