AUTOMATIC TRANSMISSION SYSTEM(for 2GR-FKS), Diagnostic DTC:P281613

DTC Code DTC Name
P281613 Pressure Control Solenoid "H" Circuit Open

DESCRIPTION

Based on the ON-OFF combinations of the shift solenoid valves SL1, SL2, SL3, SL4 and SL5, the ECM performs gear shifts from 1st gear to 8th gear.

If a circuit related to a shift solenoid valve is open or shorted, the ECM uses the fail-safe function to turn other shift solenoid valves ON or OFF. If all shift solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short has occurred, the ECM cuts power to the malfunctioning shift solenoid valve.

Tech Tips

The following table shows normal operation of the shift solenoid valve SL5 when the shift lever is in D.

Shift Solenoid Valve Operation:
Gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Shift Solenoid Valve SL5 OFF ON OFF OFF OFF OFF OFF ON
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P281613 Pressure Control Solenoid "H" Circuit Open While the vehicle is being driven so that gear changes occur, a short or open is detected in the shift solenoid valve SL5 circuit for 1 second (1-trip detection logic).

  • Harness and connector

  • Transmission wire

  • Shift solenoid valve SL5

  • ECM

 Comes on DTC stored SAE Code: P2819

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL5 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

The ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the open or short circuited solenoid.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Tech Tips

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for 2 minutes or more.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine.

  7. Perform the D Position Shift Test inspection in Road Test.

    Click here

  8. Stop the vehicle.

  9. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  10. Input the DTC: P281613.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

B003TVYE07
*a Shift Solenoid Valve SL5
*b Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL5) - ECM)


    1. Disconnect the F103 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F103-10 (SL5+) - F103-11 (SL5-) 20°C (68°F) 5.0 to 5.6 Ω
      F103-10 (SL5+) or F103-11 (SL5-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  2. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the F128 transmission wire connector.

    2. Disconnect the F103 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F128-5 (SL5+) - F103-10 (SL5+) Always Below 1 Ω
      F128-6 (SL5-) - F103-11 (SL5-) Always Below 1 Ω
      F128-5 (SL5+) or F103-10 (SL5+) - Body ground Always 10 kΩ or higher
      F128-6 (SL5-) or F103-11 (SL5-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT SHIFT SOLENOID VALVE SL5


    1. B003VU8C19
      *1 Shift Solenoid Valve SL5

      Remove the shift solenoid valve SL5.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the shift solenoid valve SL5 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve connector. Check that the valve moves and makes an operating sound.

      OK
      Valve moves and makes an operating sound.
      Result
      Proceed to
      OK
      NG

    OK

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE SHIFT SOLENOID VALVE SL5 Click here