AUTOMATIC TRANSMISSION SYSTEM(for 2GR-FKS), Diagnostic DTC:P276512, P276514, P276531

DTC Code DTC Name
P276512 Input/Turbine Speed Sensor "B" Circuit Short to Battery
P276514 Input/Turbine Speed Sensor "B" Circuit Short to Ground or Open
P276531 Input/Turbine Speed Sensor "B" No Signal

DESCRIPTION

The transmission revolution sensor (NC3) detects the automatic transmission No. 3 clutch drum rotation speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P276512 Input/Turbine Speed Sensor "B" Circuit Short to Battery

All of the following conditions are met (1-trip detection logic):


  • The battery voltage is 8 V or more.

  • The engine switch is on (IG).

  • The starter is off.

  • Transmission revolution sensor (NC3) input voltage is higher than 1.9 V for 4.5 seconds.

  • Harness and connector

  • Transmission wire

  • Transmission revolution sensor (NC3)

  • ECM

 Comes on DTC stored SAE Code: P07C2
P276514 Input/Turbine Speed Sensor "B" Circuit Short to Ground or Open

All of the following conditions are met (1-trip detection logic):


  • The battery voltage is 8 V or more.

  • The engine switch is on (IG).

  • The starter is off.

  • Transmission revolution sensor (NC3) input voltage is less than 0.1 V for 4.5 seconds or more.

  • Harness and connector

  • Transmission wire

  • Transmission revolution sensor (NC3)

  • ECM

 Comes on DTC stored SAE Code: P07C1
P276531 Input/Turbine Speed Sensor "B" No Signal

All of the following conditions are met (1-trip detection logic):


  • The battery voltage is 8 V or more.

  • The park/neutral position switch assembly D input signal is ON.

  • Transmission revolution sensor (SP2) value is 32 km/h (20 mph) or more.

  • Transmission revolution sensor (NT) value is 740 rpm or more.

  • The transmission revolution sensor (NC3) value is less than 300 rpm for 5 seconds or more.

  • Harness and connector

  • Transmission wire

  • Transmission revolution sensor (NC3)

  • ECM

 Comes on DTC stored SAE Code: P2767

MONITOR DESCRIPTION

The NC3 terminal of the ECM detects a pulse signal from the transmission revolution sensor (NC3) (input RPM). The ECM calculates gear shifts comparing the transmission revolution sensor (NT) with the transmission revolution sensors (NC3 and SP2).

While the vehicle is being driven in 3rd, 4th, 5th, 6th or 7th gear with the shift lever in D, if the No. 3 clutch drum speed is less than 300 rpm* when the output shaft speed is 32 km/h (19.89 mph) or more, the ECM determines that there is a malfunction, illuminates the MIL and stores a DTC.

*: Pulse is not output or is irregularly output.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Tech Tips

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for 2 minutes or more.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine.

  7. Perform the D Position Shift Test inspection in Road Test.

    Click here

  8. Stop the vehicle.

  9. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  10. Input the DTC: P276512, P276514 or P276531.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

B003WR9E03
*a Transmission Revolution Sensor (NC3)
*b Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Data List.

    7. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      NC3 Sensor Speed No. 3 clutch drum speed

      Min.: 0 rpm

      Max.: 12750 rpm

      • 0 rpm: 2nd or 8th gear

      • Above 0 rpm: 1st, 3rd, 4th, 5th, 6th or 7th gear

      		 Data is displayed in increments of 50 rpm.

      Tech Tips


      • NC3 Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

      • NC3 Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 32 km/h (19.89 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction of the circuit.

PROCEDURE


  1. READ VALUE USING GTS (NC3 SENSOR VOLTAGE AND NC3 SENSOR SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Transmission / Data List.

    5. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      NC3 Sensor Voltage NC3 sensor voltage

      Min.: 0.000 V

      Max.: 4.999 V

      		 0.1 to 1.9 V: Engine idling -
      NC3 Sensor Speed No. 3 clutch drum speed

      Min.: 0 rpm

      Max.: 12750 rpm

      • 0 rpm: 2nd or 8th gear

      • Above 0 rpm: 1st, 3rd, 4th, 5th, 6th or 7th gear

      		 Data is displayed in increments of 50 rpm.

      Powertrain > Transmission > Data List
      Tester Display
      NC3 Sensor Voltage
      NC3 Sensor Speed
      Result
      Result Proceed to
      Data List values are normal A
      Data List values are not normal B

    A

    GO TO STEP 5 Click here

    B

  2. INSPECT TRANSMISSION REVOLUTION SENSOR (NC3 TERMINAL)


    1. B003UDYC89
      *a

      Front view of wire harness connector

      (to Transmission Wire)

      Disconnect the F128 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F128-12 (NC3O) - Body ground Always 99 to 101 Ω

    3. Turn the engine switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      F128-11 (NC3B) - Body ground Engine switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  3. INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NC3))


    1. B003UEZC07
      *a

      Front view of wire harness connector

      (to Transmission Revolution Sensor (NC3))
      *b

      Component without harness connected

      (Transmission Wire)

      Disconnect the transmission revolution sensor (NC3) connector.

      Click here

    2. Disconnect the F128 transmission wire connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      Terminal 1 of the transmission revolution sensor (NC3) connector - 11 (NC3B) Always Below 1 Ω
      Terminal 2 of the transmission revolution sensor (NC3) connector - 12 (NC3O) Always Below 1 Ω
      Terminal 1 of the transmission revolution sensor (NC3) connector or 11 (NC3B) - Body ground Always 10 kΩ or higher
      Terminal 2 of the transmission revolution sensor (NC3) connector or 12 (NC3O) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TRANSMISSION REVOLUTION SENSOR (NC3) Click here

    NG

    REPAIR OR REPLACE TRANSMISSION WIRE Click here

  4. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the F128 transmission wire connector.

    2. Disconnect the F103 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F128-11 (NC3B) - F103-78 (NC3B) Always Below 1 Ω
      F128-12 (NC3O) - F103-110 (NC3O) Always Below 1 Ω
      F128-11 (NC3B) or F103-78 (NC3B) - Body ground Always 10 kΩ or higher
      F128-12 (NC3O) or F103-110 (NC3O) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here