FUEL SENDER GAUGE ASSEMBLY INSTALLATION

PROCEDURE


  1. INSTALL NO. 2 FUEL SENDER GAUGE ASSEMBLY


    1. B003VJ9C02
      B003WAF Slide

      Slide the No. 2 fuel sender gauge assembly downward and engage the claw (A) to install the No. 2 fuel sender gauge assembly.

      Note


      • Do not touch the resistance plate or contacts of the No. 2 fuel sender gauge assembly.

      • Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.

    2. Connect the No. 2 fuel sender gauge assembly connector.

  2. INSTALL FUEL TANK VENT TUBE ASSEMBLY


    1. Install a new fuel suction tube set gasket to the fuel tank assembly.

    2. Connect the fuel return vent tube sub-assembly and set the fuel tank vent tube assembly on the fuel tank assembly.

      Note


      • Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.

      • Do not damage the fuel return vent tube sub-assembly.

      • When connecting the fuel tube connector, do not excessively pull on the fuel return vent tube sub-assembly.

    3. B003WAOC03
      *a Protrusion
      B003WAF Notch

      Align the protrusions of the fuel tank vent tube assembly with the notches in the fuel tank assembly.

    4. While pressing down on the fuel tank vent tube assembly, temporarily install the fuel pump gauge retainer.

    5. B003UFXC01
      *a Insertion Point
      *b SST (Plate)
      *c SST (Claw)
      *d SST (Bolt)

      Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

      SST
      09808-14031   ( 09808-01030, 09808-01050 )
      09808-01071

      Tech Tips

      Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

    6. While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).

    7. B003U1HC03
      *a Protrusion
      *b Groove
      *c SST (Handle)
      *d SST (Plate)
      B003U82 Front Side

      Install SST (handle) to SST (plate).

      SST
      09808-14031   ( 09808-01010, 09808-01030, 09808-01050 )
      09808-01071

    8. Using SST, rotate the fuel pump gauge retainer so that the protrusions of the fuel pump gauge retainer are aligned with the grooves in the fuel tank assembly to install the fuel tank vent tube assembly to the fuel pump gauge retainer.

      Note


      • Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

      • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

      • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

      • Do not spin SST too fast or use an impact wrench as this may result in damage to components.

      • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

      • Make sure that the fuel suction tube set gasket does not come off.

    9. Install the No. 1 fuel tube clamp.

    10. B003X1QC03
      *a Retainer
      B003WAF Push

      Connect the fuel tank EVAP/VENT tube to the fuel tank vent tube assembly and push in the retainer to engage the 2 claws.

      Note


      • Check that there is no damage or foreign matter on the connecting parts of the fuel lines.

      • After connecting the fuel tank EVAP/VENT tube, check that the fuel tank EVAP/VENT tube is securely connected by pulling on it.

    11. Connect the charcoal canister outlet hose to the fuel tank vent tube assembly.

    12. B003UP9C04
      *a Up
      *b 120°

      Connect the No. 1 fuel evaporation tube sub-assembly to the fuel tank vent tube assembly and slide the clip to secure it.

      Tech Tips

      Engage the clip within the area shown in the illustration.

  3. INSTALL REAR FLOOR SERVICE HOLE COVER


    1. Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.

    2. Clean the installation surfaces of the rear floor service hole cover and vehicle body.

    3. Connect the fuel tank vent tube assembly connector.

    4. Install the rear floor service hole cover with new butyl tape.

  4. INSTALL FUEL SENDER GAUGE ASSEMBLY


    1. B003UM3C01
      B003WAF Slide

      Slide the fuel sender gauge assembly downward and engage the claw (A) to install the fuel sender gauge assembly.

      Note


      • Do not touch the resistance plate or contacts of the fuel sender gauge assembly.

      • Be careful not to bend the arm of the fuel sender gauge assembly.

    2. Connect the fuel sender gauge assembly connector.

  5. INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

    Click here