CAMSHAFT COMPONENTS
ILLUSTRATION
| *A | w/ Oil Cooler | - | - |
| *1 | BATTERY | *2 | IGNITION COIL ASSEMBLY |
| *3 | NO. 1 BATTERY TRAY SUPPORT | *4 | NO. 1 RADIATOR HOSE |
| *5 | NO. 1 WATER BY-PASS PIPE | *6 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
| *7 | NO. 2 RADIATOR HOSE | *8 | SPARK PLUG |
| *9 | ENGINE OIL LEVEL DIPSTICK | *10 | RADIATOR HOSE HOSE CLAMP |
| *11 | BATTERY INSULATOR | *12 | NEGATIVE BATTERY CABLE |
| *13 | POSITIVE BATTERY CABLE | *14 | BATTERY CLAMP |
| *15 | O-RING | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | INLET HEATER WATER HOSE A | *2 | NO. 2 WATER BY-PASS HOSE |
| *3 | NO. 2 WATER BY-PASS PIPE | *4 | NO. 6 WATER BY-PASS HOSE |
| *5 | OUTLET HEATER WATER HOSE A | *6 | UNION TO CONNECTOR TUBE HOSE |
| *7 | VACUUM PUMP ASSEMBLY | *8 | WATER OUTLET SUB-ASSEMBLY |
| *9 | WIRE HARNESS | *10 | WIRE HARNESS CLAMP BRACKET |
| *11 | WATER HOSE SET | *12 | O-RING |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY | *2 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *3 | SPARK PLUG TUBE GASKET | *4 | CYLINDER HEAD COVER GASKET |
| *5 | CAMSHAFT BEARING CAP OIL HOLE GASKET RH | *6 | VVT SENSOR (for Intake Side of Bank 1) |
| *7 | VVT SENSOR (for Exhaust Side of Bank 1) | *8 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Toyota Genuine Adhesive 1324, ThreeBond 1324 or equivalent | ★ | Precoated part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | *2 | SPARK PLUG TUBE GASKET |
| *3 | OIL FILLER CAP SUB-ASSEMBLY | *4 | CYLINDER HEAD COVER GASKET |
| *5 | CAMSHAFT BEARING CAP OIL HOLE GASKET LH | *6 | VVT SENSOR (for Exhaust Side of Bank 2) |
| *7 | VVT SENSOR (for Intake Side of Bank 2) | *8 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Toyota Genuine Adhesive 1324, ThreeBond 1324 or equivalent | ★ | Precoated part |
ILLUSTRATION
| *1 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1) | *2 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1) |
| *3 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2) | *4 | CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2) |
| *5 | WIRE HARNESS CLAMP BRACKET | *6 | O-RING |
| |
N*m (kgf*cm, ft.*lbf) : Specified torque | ● | Non-reusable part |
| |
Toyota Genuine Adhesive 1324, ThreeBond 1324 or equivalent | ★ | Precoated part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH |
| *3 | CAMSHAFT TIMING GEAR ASSEMBLY | *4 | CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1) |
| *5 | CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1) | *6 | CHAIN SUB-ASSEMBLY |
| *7 | NO. 1 CAMSHAFT BEARING CAP | *8 | NO. 1 CHAIN TENSIONER ASSEMBLY |
| *9 | NO. 2 CAMSHAFT | *10 | NO. 2 CAMSHAFT BEARING CAP |
| *11 | NO. 2 CHAIN TENSIONER ASSEMBLY | *12 | NO. 5 CAMSHAFT BEARING CAP |
| *13 | NO. 6 CAMSHAFT BEARING CAP | *14 | NO. 8 CAMSHAFT BEARING CAP |
| *15 | TIMING CHAIN COVER PLATE | *16 | TIMING GEAR OR CHAIN COVER PLATE GASKET |
| *17 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1) | *18 | FUEL PUMP LIFTER HOUSING |
| |
N*m (kgf*cm, ft.*lbf) : Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH | *2 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *3 | CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2) | *4 | CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2) |
| *5 | CHAIN SUB-ASSEMBLY | *6 | NO. 3 CAMSHAFT BEARING CAP |
| *7 | NO. 3 CAMSHAFT SUB-ASSEMBLY | *8 | NO. 3 CHAIN TENSIONER ASSEMBLY |
| *9 | NO. 4 CAMSHAFT BEARING CAP | *10 | NO. 4 CAMSHAFT SUB-ASSEMBLY |
| *11 | NO. 7 CAMSHAFT BEARING CAP | *12 | NO. 8 CAMSHAFT BEARING CAP |
| *13 | NO. 9 CAMSHAFT BEARING CAP | *14 | NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2) |
| |
N*m (kgf*cm, ft.*lbf) : Specified torque | - | - |