ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | V-BANK COVER SUB-ASSEMBLY | *2 | INLET NO. 1 AIR CLEANER |
| *3 | AIR CLEANER CAP WITH AIR CLEANER HOSE | *4 | AIR CLEANER CASE SUB-ASSEMBLY |
| *5 | AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY | *6 | ENGINE UNDER COVER |
| *7 | NO. 2 ENGINE UNDER COVER | *8 | REAR ENGINE UNDER COVER LH |
| *9 | REAR ENGINE UNDER COVER RH | *10 | FRONT SUSPENSION MEMBER BRACE |
| *11 | COOL AIR INTAKE DUCT SEAL | *12 | NO. 1 FUEL VAPOR FEED HOSE |
| *13 | NO. 2 VENTILATION HOSE | *14 | AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | *B | w/ Transmission Oil Cooler |
| *1 | ENGINE ROOM ECU COVER | *2 | NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
| *3 | SUCTION HOSE | *4 | OUTLET HEATER WATER HOSE A |
| *5 | INLET HEATER WATER HOSE A | *6 | FUEL TUBE SUB-ASSEMBLY |
| *7 | O-RING | *8 | UNION TO CONNECTOR TUBE HOSE |
| *9 | NO. 1 RADIATOR HOSE | *10 | NO. 2 RADIATOR HOSE SUB-ASSEMBLY |
| *11 | WATER HOSE SET | *12 | NO. 1 ENGINE ROOM RELAY BLOCK COVER |
| *13 | FUEL PIPE CLAMP | *14 | INLET NO. 1 OIL COOLER HOSE |
| *15 | OUTLET NO. 1 OIL COOLER HOSE | *16 | NO. 2 FUEL TUBE SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *A | for RHD | *B | w/ Transmission Oil Cooler |
| *1 | ENGINE ROOM ECU COVER | *2 | NO. 1 COOLER REFRIGERANT DISCHARGE HOSE |
| *3 | SUCTION HOSE | *4 | OUTLET HEATER WATER HOSE A |
| *5 | INLET HEATER WATER HOSE A | *6 | FUEL TUBE SUB-ASSEMBLY |
| *7 | O-RING | *8 | UNION TO CONNECTOR TUBE HOSE |
| *9 | NO. 1 RADIATOR HOSE | *10 | NO. 2 RADIATOR HOSE SUB-ASSEMBLY |
| *11 | WATER HOSE SET | *12 | NO. 1 ENGINE ROOM RELAY BLOCK COVER |
| *13 | FUEL PIPE CLAMP | *14 | INLET NO. 1 OIL COOLER HOSE |
| *15 | OUTLET NO. 1 OIL COOLER HOSE | *16 | NO. 2 FUEL TUBE SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE WIRE | *2 | NO. 2 ENGINE WIRE |
| *3 | NO. 3 ENGINE WIRE | *4 | NO. 4 ENGINE WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE WIRE | *2 | NO. 2 ENGINE WIRE |
| *3 | NO. 3 ENGINE WIRE | *4 | NO. 4 ENGINE WIRE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE ASSEMBLY WITH TRANSMISSION | *2 | SUSPENSION TOWER DAMPER |
| *3 | FRONT SHOCK ABSORBER ASSEMBLY LH | *4 | STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY |
| *5 | FRONT UPPER NO. 2 SUSPENSION MEMBER | *6 | FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY |
| *7 | FRONT LOWER SUSPENSION MEMBER PROTECTOR | *8 | FRONT LOWER BALL JOINT ASSEMBLY LH |
| *9 | WIRE HARNESS | *10 | STRUT BAR BRACKET REINFORCEMENT RH |
| *11 | STRUT BAR BRACKET REINFORCEMENT LH | *12 | NO. 2 EARTH WIRE |
| *13 | FRONT NO. 2 STABILIZER BRACKET LH | *14 | FRONT NO. 2 STABILIZER BRACKET RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE ASSEMBLY WITH TRANSMISSION | *2 | SUSPENSION TOWER DAMPER |
| *3 | FRONT SHOCK ABSORBER ASSEMBLY LH | *4 | STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY |
| *5 | FRONT UPPER NO. 2 SUSPENSION MEMBER | *6 | FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY |
| *7 | FRONT LOWER SUSPENSION MEMBER PROTECTOR | *8 | FRONT LOWER BALL JOINT ASSEMBLY LH |
| *9 | WIRE HARNESS | *10 | STRUT BAR BRACKET REINFORCEMENT RH |
| *11 | STRUT BAR BRACKET REINFORCEMENT LH | *12 | NO. 2 EARTH WIRE |
| *13 | FRONT NO. 2 STABILIZER BRACKET LH | *14 | FRONT NO. 2 STABILIZER BRACKET RH |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/o ATF Warmer | - | - |
| *1 | EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: Front Catalyst) | *2 | EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: Front Catalyst) |
| *3 | REAR ENGINE MOUNTING INSULATOR | *4 | REAR ENGINE MOUNTING BRACKET |
| *5 | ENGINE OIL LEVEL DIPSTICK GUIDE | *6 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE |
| *7 | AUTOMATIC TRANSMISSION ASSEMBLY | *8 | STARTER ASSEMBLY |
| *9 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT | *10 | FLYWHEEL HOUSING SIDE COVER |
| *11 | O-RING | *12 | ENGINE OIL LEVEL DIPSTICK |
| *13 | GASKET | *14 | WIRE HARNESS |
| *15 | REAR ENGINE MOUNTING MEMBER | *16 | NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY |
| *17 | OIL COOLER TUBE SUB-ASSEMBLY | *18 | STARTER COVER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| *a | Black: x 1 Silver: x 5 |
- | - |
ILLUSTRATION
| *1 | FRONT ENGINE MOUNTING INSULATOR | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *4 | CRANK ANGLE SENSOR PLATE |
| *5 | REAR DRIVE PLATE SPACER | *6 | ENGINE UNDER COVER SUB-ASSEMBLY LH |
| *7 | ENGINE UNDER COVER SUB-ASSEMBLY RH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Adhesive 1324 |
| ★ | Precoated part | - | - |