ENGINE UNIT INSTALLATION

PROCEDURE


  1. INSTALL IGNITION COIL ASSEMBLY

    Click here

  2. INSTALL V-BANK COVER BRACKET SUB-ASSEMBLY


    1. Install the V-bank cover bracket sub-assembly to the cylinder head cover sub-assembly RH with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the camshaft housing sub-assembly RH with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  4. INSTALL NO. 3 FUEL PIPE SUB-ASSEMBLY

    Click here

  5. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

    Click here

  6. INSTALL FUEL PUMP ASSEMBLY

    Click here

  7. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

    Click here

  8. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

  9. INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

    Click here

  10. INSTALL INTAKE MANIFOLD

    Click here

  11. INSTALL NO. 3 WATER BY-PASS PIPE


    1. Connect the No. 9 water by-pass hose to the rear water by-pass joint and slide the clip to secure it.

    2. Connect the No. 8 water by-pass hose to the water outlet pipe assembly and slide the clip to secure it.

    3. Install the No. 3 water by-pass pipe to the camshaft housing sub-assembly RH with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  12. INSTALL NO. 2 SURGE TANK STAY


    1. Install the No. 2 surge tank stay to the camshaft housing sub-assembly LH with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the 2 clamps to the No. 2 surge tank stay.

  13. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

    Click here

  14. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  15. INSTALL INJECTOR DRIVER

    Click here

  16. INSTALL ENGINE WIRE


    1. Install the engine wire to the engine assembly.

  17. INSTALL WATER PUMP PULLEY

  18. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

  19. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    1. Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

    2. Connect the 2 clamps.

  20. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    1. Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  21. INSTALL COMPRESSOR AND MAGNETIC CLUTCH (for 2WD)

    Click here

  22. INSTALL GENERATOR ASSEMBLY

    Click here

  23. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

    Click here

  24. INSTALL NO. 1 ENGINE COVER

    Click here

  25. INSTALL NO. 2 ENGINE COVER


    1. Install the No. 2 engine cover with the 3 clips.

    2. Connect the clamp to the No. 2 engine cover.

  26. INSTALL V-RIBBED BELT

    Click here