SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P0088

DTC Code DTC Name
P0088 Fuel Rail / System Pressure - Too High

DESCRIPTION

Refer to DTC P0087.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High

ECM did not command fuel pump for high pressure to open spill control valve, but fuel pressure increases 3 MPa (30.6 kgf/cm2, 435 psi) from target pressure for about 10 seconds (1 trip detection logic).

  • Fuel pump for high pressure

  • Fuel relief valve

  • Fuel delivery pipe sub-assembly (fuel pressure sensor)

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION

If the fuel pressure increases despite a decrease request signal being sent to the fuel pump (for high pressure) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel pressure sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Record the Freeze Frame Data.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG) and turn the GTS on.

  7. Start the engine.

  8. Based on engine speed, engine load and other freeze frame data stored in the ECM, reproduce the conditions present when the DTC was stored.

  9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  12. Input the DTC: P0088.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P0088 is output A
      DTC P0088 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0088 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR)


    1. Connect the GTS to the DLC3.

    2. Start the engine and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Press.


      Powertrain > Engine > Data List
      Tester Display
      Fuel Press

    4. Check that the fuel pressure fluctuates when the engine is raced.

      OK
      Fuel pressure fluctuates.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FUEL DELIVERY PIPE SUB-ASSEMBLY (FUEL PRESSURE SENSOR) Click here

    OK

  3. REPLACE FUEL PUMP (FOR HIGH PRESSURE)


    1. Replace the fuel pump (for high pressure).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0088 IS OUTPUT AGAIN)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.

      Click here


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait at for least 30 seconds.

    6. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P0088 is output A
      DTCs are not output B

    B

    END

    A

  5. INSPECT FUEL RELIEF VALVE ASSEMBLY


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Fuel Press.


      Powertrain > Engine > Data List
      Tester Display
      Fuel Press

    5. Start the engine.

    6. Check the fuel pressure.

      Result
      GTS Display Result Proceed to
      Fuel Press Less then 15300 kPag A
      15300 kPag or higher B

    A

    REPLACE ECM Click here

    B

    REPLACE FUEL RELIEF VALVE ASSEMBLY Click here