SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P2014, P2016, P2017

DTC Code DTC Name
P2014 Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1)
P2016 Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1)
P2017 Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1)

DESCRIPTION

The Swirl Control Valve (SCV) position sensor is a non-contact type sensor.

The position sensor measures the opening angle of the swirl control valve. The sensor is reliable and accurate, as it is electrically controlled by Hall-effect elements.

A01MU96E06
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2014 Intake Manifold Runner Position Sensor / Switch Circuit (Bank 1) The swirl control valve position sensor output voltage flutters up and down beyond the normal operating range (less than 0.2 V, or higher than 4.8 V) for more than 0.5 seconds (open or short) (1 trip detection logic).

  • Open or short in swirl control valve position sensor circuit

  • Swirl control valve position sensor (built into intake air control valve actuator)

  • ECM

 Comes on DTC stored
P2016 Intake Manifold Runner Position Sensor / Switch Circuit Low (Bank 1) The swirl control valve position sensor output voltage is less than 0.2 V for more than 0.5 seconds (short) (1 trip detection logic).

  • Open or short in swirl control valve position sensor circuit

  • Swirl control valve position sensor (built into intake air control valve actuator)

  • ECM

 Comes on DTC stored
P2017 Intake Manifold Runner Position Sensor / Switch Circuit High (Bank 1) The swirl control valve position sensor output voltage is higher than 4.8 V for more than 0.5 seconds (open) (1 trip detection logic).

  • Open or short in swirl control valve position sensor circuit

  • Swirl control valve position sensor (built into intake air control valve actuator)

  • ECM

 Comes on DTC stored

Tech Tips

When DTC P2014, P2016 or P2017 is output, use the GTS to confirm the IAC Sensor Voltage (swirl control valve position sensor output voltage). Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IAC Sensor Voltage.

IAC Sensor Voltage Malfunction
0.2 V or less

  • IAC1 circuit shorted

  • VC circuit open
4.8 V or higher

  • VC and IAC1 circuits shorted

  • IAC1 circuit open

  • E2 circuit open

MONITOR DESCRIPTION

The ECM IAC1 terminal voltage increases in correlation with the opening angle of the swirl control valve. When the swirl control valve is fully closed, approximately 0.69 V is applied to the IAC1 terminal. When the swirl control valve is fully open, approximately 3.518 V is applied to the IAC1 terminal.

When the output voltage of the IAC1 terminal deviates from the standard range, the ECM determines that a malfunction has occurred in the position sensor and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components Intake air control valve actuator (for swirl control valve position sensor)
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Swirl control valve position sensor voltage 0.2 to 4.8 V

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Wait 0.5 seconds or more.

  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  8. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  10. Input the DTC: P2014, P2016 or P2017.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P2004.

Click here

CAUTION / NOTICE / HINT

Tech Tips


  • If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. PERFORM ACTIVE TEST USING GTS (CONTROL THE SCV DUTY RATIO)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the SCV Duty Ratio / All Data / IAC Sensor Voltage.


      Powertrain > Engine > Active Test
      Active Test Display
      Control the SCV Duty Ratio
      Data List Display
      IAC Sensor Voltage

    4. Check the value of IAC Sensor Voltage while changing Control the SCV Duty Ratio from -100 to 100% (or from 100 to -100%) using the GTS.

      Standard
      The value of IAC Sensor Voltage remains between 0.2 to 4.8 V while Control the SCV Duty Ratio is changed from -100 to 100% (or from 100 to -100%).

      Tech Tips

      Control the SCV Duty Ratio Operation IAC Sensor Voltage (Normal) Suspected Trouble Area

      • IAC1 circuit shorted

      • VC circuit open

      • VC and IAC1 circuits shorted

      • IAC1 circuit open

      • E2 circuit open

      		 Sensor malfunction
      -100% 0.2 to 1.0 V Remains below 0.2 V Remains higher than 4.8 V Other than the voltage in the 2 columns on the left
      100% 3.2 to 4.8 V Remains below 0.2 V Remains higher than 4.8 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE POSITION SENSOR - ECM) Click here

    OK

  2. CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Engine > Clear DTCs

    4. Turn the engine switch off and wait for at least 30 seconds.

    5. Turn the engine switch on (IG).

    6. Turn the GTS on.

    7. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P2014, P2016 and/or P2017 is output A
      DTCs are not output B

    A

    REPLACE ECM Click here

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

  3. CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE POSITION SENSOR - ECM)


    1. Disconnect the ECM connector.

    2. Disconnect the swirl control valve position sensor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      s1-1 (VCX) - F1-18 (VC) Always Below 1 Ω
      s1-3 (VSX) - F1-30 (IAC1) Always Below 1 Ω
      s1-2 (E2X) - F1-28 (E2) Always Below 1 Ω
      s1-1 (VCX) or F1-18 (VC) - Body ground Always 10 kΩ or higher
      s1-3 (VSX) or F1-30 (IAC1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK TERMINAL VOLTAGE (POWER SOURCE OF SWIRL CONTROL VALVE POSITION SENSOR)


    1. Disconnect the sworl control valve position sensor connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      s1-1 (VCX) - Body ground Engine switch on (IG) 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ECM Click here

    OK

  5. REPLACE INTAKE AIR CONTROL VALVE ACTUATOR (FOR SWIRL CONTROL VALVE POSITION SENSOR)


    1. Replace the intake air control valve actuator (for swirl control valve position sensor).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (DTC P2014, P2016 AND/OR P2017)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Engine > Clear DTCs

    4. Turn the engine switch off and wait for at least 30 seconds.

    5. Turn the engine switch on (IG).

    6. Turn the GTS on.

    7. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    9. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P2014, P2016 and/or P2017 is output A
      DTCs are not output B

    A

    REPLACE ECM Click here

    B

    END