SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P019515

DTC Code DTC Name
P019515 Engine Oil Temperature Sensor Circuit Short to Battery or Open

DESCRIPTION

Refer to DTC P019511.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019515 Engine Oil Temperature Sensor Circuit Short to Battery or Open The engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more (1 trip detection logic).

  • Open or short in engine oil temperature sensor circuit

  • Engine oil temperature sensor

  • ECM

 Does not come on DTC stored

SAE Code:

P0198

Tech Tips

When this DTC is output, check the Engine Oil Temperature Sensor in the Data List. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.

DTC No. Engine Oil Temperature Sensor Malfunction
P019515 -40°C (-40°F)

  • Short to +B in THEO circuit

  • Open in THEO circuit

  • Open in ETHE circuit

If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

The ECM monitors the engine oil temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor circuit is malfunctioning and stores this DTC.

Example:

If the engine oil temperature sensor output voltage is higher than 4.93 V for 5 seconds or more, the ECM store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine and wait for the time indicated below.


    • If the engine oil temperature sensor is higher than -10°C (14°F): 15 seconds or more.

    • If the engine oil temperature sensor is -10°C (14°F) or less: 13 minutes or more.

  7. Enter the following menus: Powertrain / Engine / Trouble Codes.

  8. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  10. Input the DTC: P019515.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P019511.

Click here

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

    A01MVPPC08
    *1 Engine Oil Temperature Sensor *2 ECM
    *a

    Front view of wire harness connector

    (to Engine Oil Temperature Sensor)

    		 - -

    1. Disconnect the engine oil temperature sensor connector.

    2. Connect terminals 1 and 2 of the engine oil temperature sensor connector on the wire harness side.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.


      Powertrain > Engine > Data List
      Tester Display
      Engine Oil Temperature Sensor

    7. Read the value displayed on the GTS.

      Standard Value
      164°C (327°F) or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ENGINE OIL TEMPERATURE SENSOR Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)


    1. Disconnect the engine oil temperature sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I3-2 - F78-97 (THEO) Always Below 1 Ω
      I3-1 - F78-96 (ETHE) Always Below 1 Ω
      I3-2 or F78-97 (THEO) - Other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR