SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P001013

DTC Code DTC Name
P001013 A Camshaft Position Actuator Bank 1 Circuit Open

DESCRIPTION

The Variable Valve Timing (VVT) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The cam timing oil control solenoid assembly operates according to signals received from the ECM to control the position of the camshaft timing oil control valve assembly and supply engine oil. The camshaft timing oil control valve assembly moves when the ECM applies 12 V to the cam timing oil control solenoid assembly. The ECM changes the energizing time of the cam timing oil control solenoid assembly (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

B003TKQE02
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001013 A Camshaft Position Actuator Bank 1 Circuit Open Open or short in cam timing oil control solenoid assembly circuit (1 trip detection logic).

  • Open or short in cam timing oil control solenoid assembly circuit

  • Cam timing oil control solenoid assembly

  • ECM

 Comes on DTC stored SAE Code: P0010

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the cam timing oil control solenoid assembly circuit. If the cam timing oil control solenoid assembly duty-cycle is excessively high or low while the engine switch is on (IG) or the engine is running, the ECM will illuminate the MIL and store this DTC.

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch is on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch is on (IG) and turn the GTS on.

  6. Wait 5 seconds.

  7. Enter the following menus: Powertrain / Engine / Trouble Codes.

  8. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  10. Input the DTC: P001013.

  11. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

A01MWWPE43
*a Cam Timing Oil Control Solenoid Assembly

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ OUTPUT DTC (DTC P001013)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTC after recording the freeze frame data and DTC.


      Powertrain > Engine > Clear DTCs

    5. Turn the engine switch off and wait for at least 30 seconds.

    6. Start the engine.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P001013 is output A
      DTCs are not output B

    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY


    1. Inspect the cam timing oil control solenoid assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (CAM TIMING OIL CONTROL SOLENOID ASSEMBLY - ECM)


    1. Disconnect the cam timing oil control solenoid assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F86-2 - F78-9 (OC1+) Always Below 1 Ω
      F86-1 - F78-8 (OC1-) Always Below 1 Ω
      F86-2 or F78-9 (OC1+) - Body ground and other terminals Always 10 kΩ or higher
      F86-1 or F78-8 (OC1-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR