СИСТЕМА ЗАПУСКА И ОСТАНОВА (для моделей с 3ZR-FAE), Diagnostic DTC:P2531

DTC Code DTC Name
P2531 Ignition Switch Run Position Circuit Low

DESCRIPTION

If the engine stop and start ECU receives the off signal from the certification ECU (smart key ECU assembly) when communication with the ECM is normal, the engine stop and start ECU will store DTC P2531.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P2531 Ignition Switch Run Position Circuit Low

Both of the following conditions are met for 10 seconds or more (1 trip detection logic):


  • Ignition switch off signal is input.

  • Communication with the ECM is normal.

  • Wire harness or connector

  • IG2 relay

  • EFI-MAIN NO. 1 relay

  • Certification ECU (Smart key ECU assembly)

  • Engine stop and start ECU

 Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here


  1. Tech Tips


    • If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    6. Depress the brake pedal and stop the vehicle.

    7. Keep the engine stopped by stop and start control for 10 second or more. (Keep the shift lever in D.)

    8. Release the brake pedal with the shift lever in D to start the engine.

    9. Check that DTCs are not output.

      Click here


      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips

    If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 40 minutes until refresh charge is completed and stop and start control operation is permitted.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. Depress the brake pedal and stop the vehicle.

    5. Allow the engine to stop by stop and start control. (Keep the shift lever in D.)

    6. Release the brake pedal with the shift lever in D to start the engine.

WIRING DIAGRAM

A01KBZ2E03
A01KBW6E03

CAUTION / NOTICE / HINT

Note


  • When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click here

PROCEDURE


  1. READ VALUE USING GTS (IG SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.

    5. According to the display on the GTS, read the Data List.


      Powertrain > Stop and Start > Data List
      Tester Display
      IG Switch
      Result
      Tester Display Result Proceed to
      IG Switch ON A
      OFF B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - IG2 RELAY)


    1. Disconnect the G87 engine stop and start ECU connector.

    2. Remove the IG2 relay from engine room relay block and junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G87-20 (IG2) - IG2 relay terminal 5 Always Below 1 Ω
      G87-20 (IG2) - Body ground Always 10 kΩ or higher
      IG2 relay terminal 5 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT RELAY (IG2 RELAY)


    1. Inspect the IG2 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (IG2-MAIN RELAY)

    OK

  4. CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND)


    1. Remove the IG2 relay from engine room relay block and junction block assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      IG2 relay terminal 2 - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (IG2 RELAY - IGNITION OR STARTER SWITCH ASSEMBLY OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))


    1. Remove the IG2 relay from engine room relay block and junction block assembly.

    2. w/ Entry and Start System:

      Disconnect the G82 certification ECU (smart key ECU assembly) connector.

    3. w/o Entry and Start System:

      Disconnect the G4 ignition or starter switch assembly connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/ Entry and Start System
      Tester Connection Condition Specified Condition
      IG2 relay terminal 1 - G82-9 (IG2D) Always Below 1 Ω
      IG2 relay terminal 1 - Body ground Always 10 kΩ or higher
      G82-9 (IG2D) - Body ground Always 10 kΩ or higher
      w/o Entry and Start System
      Tester Connection Condition Specified Condition
      IG2 relay terminal 1 - G4-3 (IG2) Always Below 1 Ω
      IG2 relay terminal 1 - Body ground Always 10 kΩ or higher
      G4-3 (IG2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)


    1. Disconnect the A65 engine stop and start ECU connector.

    2. Remove the EFI-MAIN NO. 1 relay from engine room relay block and junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A65-5 (+B) - EFI-MAIN NO. 1 relay terminal 3 Always Below 1 Ω
      A65-5 (+B) - Body ground Always 10 kΩ or higher
      EFI-MAIN NO. 1 relay terminal 3 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK ECM (IGSW TERMINAL VOLTAGE)


    1. A01KCMPC19
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A62-6 (IGSW) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    GO TO ECM POWER SOURCE CIRCUIT Click here

    OK

  8. INSPECT RELAY (EFI-MAIN NO. 1 RELAY)


    1. Inspect the EFI-MAIN NO. 1 relay.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE RELAY (EFI-MAIN NO. 1 RELAY)

    OK

  9. CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM)

    Tech Tips

    If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN NO. 1 relay circuit is suspected.


    1. Remove the EFI-MAIN NO. 1 relay from engine room relay block and junction block assembly.

    2. Disconnect the A62 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      EFI-MAIN NO. 1 relay terminal 1 - A62-46 (MREL) Always Below 1 Ω
      EFI-MAIN NO. 1 relay terminal 1 - Body ground Always 10 kΩ or higher
      A62-46 (MREL) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK (w/ Entry and Start System)
      OK (w/o Entry and Start System)
      NG

    OK (w/o Entry and Start System)

    INSPECT IGNITION OR STARTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK (w/ Entry and Start System)

  10. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (IG2D TERMINAL VOLTAGE)

    A01KCEOC67
    *a

    Component with harness connected

    (Certification ECU (Smart Key ECU Assembly))

    		 - -

    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G82-9 (IG2D) - Body ground Ignition switch ACC Below 1 V
      G82-9 (IG2D) - Body ground Ignition switch ON 9 V or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  11. INSPECT IGNITION OR STARTER SWITCH ASSEMBLY


    1. Inspect the ignition or starter switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ENGINE STOP AND START ECU Click here

    NG

    REPLACE IGNITION OR STARTER SWITCH ASSEMBLY Click here