СИСТЕМА ЗАПУСКА И ОСТАНОВА (для моделей с 3ZR-FAE), Diagnostic DTC:P060B

DTC Code DTC Name
P060B Analog to Digital Converter Malfunction

DESCRIPTION

If an internal malfunction occurs in the engine stop and start ECU, it stores P060B and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P060B Analog to Digital Converter Malfunction

Both of the following conditions are met for 0.7 seconds or more (1 trip detection logic):


  • Ignition switch ON

  • Engine stop and start ECU has an internal malfunction

 Engine stop and start ECU Blinks DTC stored

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs

Click here


  1. Tech Tips


    • If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

    CONFIRMATION AFTER TROUBLESHOOTING


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and warm it up.

    5. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    6. for CVT:

      Depress the brake pedal and stop the vehicle.

      for Manual Transaxle:

      Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    7. Keep the engine stopped by stop and start control for 1 second or more. (for CVT: Keep the shift lever in D.)

    8. for CVT:

      Release the brake pedal with the shift lever in D to start the engine.

      for Manual Transaxle:

      Depress the clutch pedal and start the engine.

      Tech Tips

      If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.

    9. Check that DTCs are not output.

      Click here


      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips

    If the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, drive the vehicle approximately 5 to 60 minutes until refresh charge is completed and stop and start control operation is permitted.


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. for CVT:

      Depress the brake pedal and stop the vehicle.

      for Manual Transaxle:

      Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to stop by stop and start control. (for CVT: Keep the shift lever in D.)

    6. for CVT:

      Release the brake pedal with the shift lever in D to start the engine.

      for Manual Transaxle:

      Depress the clutch pedal and start the engine.

CAUTION / NOTICE / HINT

Note


  • for CVT:

    When replacing the engine stop and start ECU with a new one, make sure to download the previous status (number of starter operations) of the old engine stop and start ECU. After replacing the engine stop and start ECU, turn the ignition switch to ON and wait 20 seconds, then confirm that "OK" is displayed for the Data List item "Oper Prohibition (O/P Air Bleeding)". Then upload the previous status (number of starter operations) to the engine stop and start ECU.

    Click here

  • for Manual Transaxle:

    Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

Tech Tips

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click here

PROCEDURE


  1. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    5. Clear the DTC.


      Powertrain > Stop and Start > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT

  2. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P060B)


    1. Turn the ignition switch off and wait for 30 seconds or more.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    5. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    6. Read the DTCs.


      Powertrain > Stop and Start > Trouble Codes
      Result
      Result Proceed to
      DTC P060B is output A
      DTC P060B and other DTCs are output B
      DTCs are not output C

    A

    REPLACE ENGINE STOP AND START ECU Click here

    B

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    C

    USE SIMULATION METHOD TO CHECK Click here