СИСТЕМА БЕССТУПЕНЧАТОЙ ТРАНСМИССИИ Shift Paddle Switch Circuit

DESCRIPTION

When the shift lever is in M, the shift range can be changed using the shift paddle switches. It is also possible to select the shift range when the vehicle is being driven with the shift lever in D by operating the shift paddle switches.

WIRING DIAGRAM

A01KB8NE02

CAUTION / NOTICE / HINT

CAUTION:

Refer to the SRS precaution before troubleshooting.

w/o Occupant Classification System: Click here

w/ Occupant Classification System: Click here

Note


  • Perform initialization when parts related to the continuously variable transaxle are replaced.

    Click here

  • Check that no DTCs are stored after performing initialization.

    Click here

PROCEDURE


  1. READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

    5. According to the display on the GTS, read the Data List.


      Powertrain > Engine and ECT > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Sports Shift Up SW Sport shift up switch status ON or OFF

      • ON: "+" shift paddle operated and held (up-shift)

      • OFF: "+" shift paddle not operated (up-shift)

      		 -
      Sports Shift Down SW Sport shift down switch status ON or OFF

      • ON: "-" shift paddle operated and held (down-shift)

      • OFF: "-" shift paddle not operated (down-shift)

      		 -

      Powertrain > Engine and ECT > Data List
      Tester Display
      Sports Shift Up SW
      Sports Shift Down SW
      Result
      Result Proceed to
      Data display is within Normal Condition range A
      Data display is not within Normal Condition range B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

  2. INSPECT SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY)


    1. A01KBD0C23
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Disconnect the shift lever assembly (transmission control switch) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A62-42 (SFTU) - Body ground "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      A62-42 (SFTU) - Body ground "+" shift paddle not operated (up-shift) 1 MΩ or higher
      A62-43 (SFTD) - Body ground "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      A62-43 (SFTD) - Body ground "-" shift paddle not operated (down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    GO TO TRANSMISSION CONTROL SWITCH CIRCUIT Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)


    1. A01KCNOC18
      *a

      Front view of wire harness connector

      (to Spiral Cable with Sensor Sub-assembly)

      Disconnect the spiral cable with sensor sub-assembly connector.

      for Dual Type: Click here

      for Single Type: Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G8-2 (ECC) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)


    1. Disconnect the G8 spiral cable with sensor sub-assembly connector.

      for Dual Type: Click here

      for Single Type: Click here

    2. Disconnect the A62 ECM connector.

    3. Disconnect the G36 shift lever assembly (transmission control switch) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G8-7 (SDN) - A62-43 (SFTD) Always Below 1 Ω
      G8-14 (SUP) - A62-42 (SFTU) Always Below 1 Ω
      G8-7 (SDN) or A62-43 (SFTD) - Body ground Always 10 kΩ or higher
      G8-14 (SUP) or A62-42 (SFTU) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - SHIFT PADDLE SWITCH)


    1. A01KBRPC18
      *a

      Steering Pad Switch Assembly Connector

      (to Spiral Cable with Sensor Sub-assembly)

      Disconnect the steering pad switch connector.

      for Dual Type: Click here

      for Single Type: Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z1-6 (SUP) - z1-7 (ECC) "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      z1-6 (SUP) - z1-7 (ECC) "+" shift paddle not operated (up-shift) 1 MΩ or higher
      z1-12 (SDN) - z1-7 (ECC) "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      z1-12 (SDN) - z1-7 (ECC) "-" shift paddle not operated (down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY) Click here

    OK

  6. INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY


    1. Inspect the spiral cable with sensor sub-assembly.

      for Dual Type: Click here

      for Single Type: Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY for Dual Type: Click here
    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY for Single Type: Click here

    OK

  7. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  8. INSPECT SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY)


    1. A01KBAKC02
      *1 Shift Paddle Switch LH

      Remove the shift paddle switch LH.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
      SFTD - ECC1 "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      SFTD - ECC1 "-" shift paddle not operated (down-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT PADDLE SWITCH LH (TRANSMISSION SHIFT SWITCH ASSEMBLY) Click here

    OK

  9. INSPECT SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY)


    1. A01KCYBC02
      *1 Shift Paddle Switch RH

      Remove the shift paddle switch RH.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SFTU - ECC1 "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      SFTU - ECC1 "+" shift paddle not operated (up-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT PADDLE SWITCH RH (TRANSMISSION SHIFT SWITCH ASSEMBLY) Click here

    OK

  10. INSPECT NO. 1 SWITCH WIRE


    1. A01KDSUC02
      *a

      No. 1 Switch Wire

      (to Steering Pad Switch Assembly)

      Disconnect the No. 1 switch wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      SFTD - ECC "-" shift paddle operated and held (down-shift) Below 2.5 Ω
      SFTD - ECC "-" shift paddle not operated (down-shift) 1 MΩ or higher
      SFTU - ECC "+" shift paddle operated and held (up-shift) Below 2.5 Ω
      SFTU - ECC "+" shift paddle not operated (up-shift) 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    NG

    REPLACE NO. 1 SWITCH WIRE Click here