ВЫПУСКНАЯ ТРУБА УСТАНОВКА

PROCEDURE


  1. INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A01VALQ

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum free length
      41.5 mm (1.63 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. Using a wire brush, remove any foreign matter from the gasket installation surface.

    3. A01V8BJC06
      *1 Gasket
      *2 Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the exhaust manifold.

      Note


      • Be sure to install the gasket so that it faces the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.

    4. Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  2. INSTALL CENTER EXHAUST PIPE ASSEMBLY


    1. Install a new gasket to the front exhaust pipe assembly.

    2. Connect the 3 exhaust pipe supports to install the center exhaust pipe assembly.

    3. Install the 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  3. INSTALL TAIL EXHAUST PIPE ASSEMBLY


    1. A01VALQ

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum free length
      38.5 mm (1.52 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. A01V8BJC06
      *1 Gasket
      *2 Wooden Block

      Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the center exhaust pipe assembly.

      Note


      • Be sure to install the gasket so that it faces the correct direction.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • When connecting the tail exhaust pipe assembly, do not push in the gasket with the tail exhaust pipe assembly.

    3. Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly.

    4. Install the 2 compression springs and 2 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  4. CONNECT HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

    Note

    Do not strike the metal part of the heated oxygen sensor.


    1. Rotate the heated oxygen sensor counterclockwise the same number of times as recorded in the removal procedure, and then connect it to the center exhaust pipe assembly by hand.

      Note

      After rotating the heated oxygen sensor counterclockwise the same number of times as in the removal procedure, connect it while making sure that the wire harness is not twisted.

    2. A01VA5ZC01
      *1 Fulcrum Length

      Using SST, tighten the heated oxygen sensor.

      SST
      09224-00010
      Torque:
      without SST
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }
      with SST
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips


      • Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

        Click here


      • Make sure SST and the wrench are connected in a straight line.

    3. Connect the grommet to the floor panel.

  5. INSPECT FOR EXHAUST GAS LEAK

    If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

    Tech Tips

    If an exhaust gas leak has been repaired, perform an inspection following the repair.

    Click here

  6. INSTALL NO. 2 ENGINE UNDER COVER

    Click here

  7. INSTALL FRONT FLOOR COVER

    Click here