ОХЛАДИТЕЛЬ РОГ УСТАНОВКА

PROCEDURE


  1. INSTALL EGR VALVE ASSEMBLY

    Click here

  2. INSTALL EGR COOLER ASSEMBLY WITH EGR VALVE ASSEMBLY


    1. Install a new water pipe to the EGR cooler assembly.

    2. Install a new gasket to the No. 2 EGR pipe sub-assembly.

      Tech Tips

      Make sure that the claw of the gasket faces the No. 2 EGR pipe sub-assembly.

    3. Temporarily install the EGR cooler assembly with EGR valve assembly with the 7 bolts.

    4. A01V6XK

      Using a T45 "TORX" socket wrench, tighten the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    5. Loosen the 2 bolts 90°.

    6. A01V8N6C02
      A01V9RL Bolt (A)
      A01V8SA Bolt (B)
      A01V7J0 Bolt (C)

      Tighten the 7 bolts (A), (B) and (C), and then 2 nuts in the order shown in the illustration.

      Torque:
      for Bolt (A)
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
      for Bolt (B)
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      for Bolt (C)
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      Tech Tips


      • When tightening the bolts (A), use a T45 "TORX" socket wrench.

      • When tightening the bolts (B), use a 6 mm hexagon wrench.

    7. Connect the vacuum hose to the EGR cooler assembly.

    8. Connect the hose clamp to the EGR cooler hose.

    9. Attach the clamp and connect the engine wire to the EGR valve assembly.

    10. Connect the EGR valve assembly connector.

  3. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. Install the No. 1 exhaust manifold heat insulator with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Attach the 2 clamps and connect the engine wire.

    3. Attach the 2 clamps and connect the air fuel ratio sensor.

    4. A01V7U8C02
      *1 Air Fuel Ratio Sensor
      *2 Bracket
      *a 1.5 mm (0.0591 in.) or less

      Lower the air fuel ratio sensor connector to the position shown in the illustration and connect the air fuel ratio sensor connector.

  4. INSTALL NO. 1 TURBO INSULATOR

    Click here

  5. CONNECT FUEL FEED PIPE SUB-ASSEMBLY


    1. Connect the fuel feed pipe sub-assembly to the fuel pipe clamp.

    2. Connect the vacuum hose to the No. 2 fuel hose.

    3. Connect the fuel feed pipe sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    4. Attach the 2 clamps and connect the engine wire.

  6. CONNECT NO. 1 AIR TUBE ASSEMBLY

    Click here

  7. INSTALL NO. 4 WATER BY-PASS HOSE

    Click here

  8. CONNECT ENGINE WIRE

    Click here

  9. CONNECT COMPRESSOR OUTLET ELBOW

    Click here

  10. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  11. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  12. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

    Click here

  13. INSTALL BATTERY BRACKET REINFORCEMENT

    Click here

  14. INSTALL BATTERY CARRIER ASSEMBLY

    Click here

  15. INSTALL BATTERY TRAY

  16. INSTALL BATTERY

  17. INSTALL BATTERY INSULATOR

  18. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  19. CONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  20. CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  21. ADD ENGINE COOLANT

    Click here

  22. INSPECT FOR COOLANT LEAK

    Click here

  23. INSTALL NO. 1 ENGINE COVER

    Click here

  24. INSTALL NO. 1 ENGINE UNDER COVER

    Click here

  25. PERFORM INITIALIZATION

    Perform EGR learning value reset.

    Click here