НАГНЕТАЮЩИЙ ТОПЛИВНЫЙ НАСОС УСТАНОВКА

CAUTION / NOTICE / HINT

Note


  • SST A remains in the timing chain cover plate.

  • Always be sure to check the tightening torque.

  • If the pressure lines are leaking after installation, they must be replaced.

  • Do not overtighten the pressure lines.

PROCEDURE


  1. INSTALL FUEL SUPPLY PUMP ASSEMBLY


    1. Install the fuel quantity control valve with the 2 bolts.

      Tech Tips

      Refer to "SPECIFICATIONS - STANDARD BOLT" for the tightening torque.

    2. A01QTMMC01
      *1 Injection Pump Drive Gear

      To insert the fuel supply pump assembly shaft in the injection pump drive gear, it may be necessary to turn the fuel supply pump assembly several degrees so that the spline indicated by the arrow in the illustration and the groove in the fuel supply pump assembly shaft are aligned. Then rotate the fuel supply pump assembly back to the position where the screw can be installed.

    3. Install the fuel supply pump assembly to the cylinder block.

      Note

      Do not damage the shaft, especially the taper.

      Tech Tips

      When installing a new fuel supply pump assembly, adjust the fuel supply pump assembly and injection pump drive gear alignment by turning the fuel supply pump assembly 45° clockwise (top view).

      A01QOOX
    4. A01QP3QN01

      Tighten the central bolt connection between the fuel supply pump assembly and injection pump drive gear.

      Torque:
      65 N*m  { 663 kgf*cm, 48 ft.*lbf }

    5. Install the 2 bolts to the fuel supply pump assembly.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
    6. A01QP7CN01

      Temporarily install the fuel supply pump assembly support with the 4 bolts by hand in the order shown in the illustration.

    7. A01QP7CN03

      Tighten the 4 bolts in the order shown in the illustration.

      Torque:
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
    8. A01QO6VN01

      Install SST B to SST A, and then remove both SST A and SST B.

      SST
      PZ4TB-04967-25

    9. Apply a light coat of engine oil to a new O-ring, and install it to the sealing cap.

    10. Install the sealing cap to the timing chain cover plate.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    11. Install 2 new clamps to the fuel feed line hose and fuel return line hose.

    12. Connect the fuel feed line hose and fuel return line hose to the fuel supply pump assembly and tighten the 2 clamps.

      Torque:
      3.0 N*m  { 31 kgf*cm, 27 in.*lbf }

    13. Connect the connector to the fuel quantity control valve.

    14. Release the No. 1 cylinder set to TDC/compression.

  2. INSTALL NO. 1 AND NO. 2 FUEL HOSE PROTECTOR


    1. A01QU7M

      Install the No. 2 fuel hose protector to the fuel feed line hose and fuel return line hose as shown in the illustration.

    2. Install the No. 1 fuel hose protector to the No. 2 fuel hose protector.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    3. Attach the clamp to connect the fuel temperature sensor connector.

  3. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

    Click here

  4. INSPECT FOR FUEL LEAK

    Click here

  5. PERFORM INITIALIZATION

    Click here