БЛОК ДВИГАТЕЛЯ УСТАНОВКА

PROCEDURE

1. INSTALL NO. 1 VACUUM PUMP BRACKET

   
   

   1. Install a new gasket and the No. 1 vacuum pump bracket with the 2 bolts.

      Torque:

      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

2. INSTALL VACUUM PUMP ASSEMBLY

   Click here

3. CONNECT UNION TO CONNECTOR TUBE HOSE

   Click here

4. INSTALL IGNITION COIL ASSEMBLY

   Click here

5. INSTALL THERMOSTAT

   Click here

6. INSTALL WATER INLET

   Click here

7. INSTALL NO. 1 WATER BY-PASS PIPE

   
   

   1. Install the No. 1 water by-pass pipe with the 2 bolts.

      Torque:

      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

8. INSTALL WATER INLET HOSE

   
   

   1. Install the water inlet hose, and slide the 2 clamps to secure the hose.

9. INSTALL WATER BY-PASS HOSE

   
   

   1. Install the water by-pass hose, and slide the clamp to secure the hose.

10. CONNECT NO. 3 WATER BY-PASS HOSE

    
    

    1. Connect the No. 3 water by-pass hose to the water inlet housing, and slide the clamp to secure the hose.

11. INSTALL PCV HOSE

    
    

    1. Install the PCV hose to the PCV valve and slide the clamp to secure it.

12. INSTALL NO. 3 WATER BY-PASS PIPE (for CVT)

    
    

    1. Install a new gasket and the No. 3 water by-pass pipe with the 2 nuts.

       Torque:

       10 N*m  { 102 kgf*cm, 7 ft.*lbf }

13. INSTALL NO. 1 SEAL PLATE (for Manual Transaxle)

    
    

    1. Install the No. 1 seal plate and new gasket with the 2 nuts.

       Torque:

       10 N*m  { 102 kgf*cm, 7 ft.*lbf }

14. INSTALL EXHAUST MANIFOLD

    Click here

15. INSTALL MANIFOLD STAY

    Click here

16. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

17. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    
    

    1. Apply a light coat of engine oil to a new O-ring.

    2. Install the O-ring to the engine oil level dipstick guide.

    3. Install the engine oil level dipstick guide with the bolt.

       Torque:

       21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    4. Install the engine oil level dipstick.

18. INSTALL FUEL INJECTOR ASSEMBLY

    Click here

19. INSTALL NO. 1 DELIVERY PIPE SPACER

    Click here

20. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

    Click here

21. INSTALL FUEL TUBE SUB-ASSEMBLY

    Click here

22. INSTALL WIRE HARNESS CLAMP BRACKET

    Click here

23. INSTALL INTAKE MANIFOLD

    Click here

24. INSTALL HEATER WATER INLET HOSE

    
    

    1. Connect the heater water inlet hose to the cylinder head sub-assembly, and slide the clamp to secure the hose.

25. INSTALL HEATER WATER OUTLET HOSE

    
    

    1. Connect the heater water outlet hose to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.

26. INSTALL AIR TUBE

    Click here

27. INSTALL THROTTLE BODY ASSEMBLY

    Click here

28. INSTALL ENGINE WIRE