БЛОК ДВИГАТЕЛЯ УСТАНОВКА
CAUTION / NOTICE / HINT
Note
-
When replacing the injectors (including shuffling the injectors between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.
-
When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.
PROCEDURE
-
INSTALL DRIVE SHAFT BEARING BRACKET
-
Install the drive shaft bearing bracket with the 3 bolts.
- Torque:
- 63.7 N*m { 650 kgf*cm, 47 ft.*lbf }
-
-
INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY
-
INSTALL NO. 2 TURBO OIL PIPE
-
INSTALL NO. 5 WATER BY-PASS PIPE
-
CONNECT NO. 3 WATER BY-PASS HOSE
-
INSTALL NO. 1 TURBO INSULATOR
-
INSTALL TURBO OIL OUTLET PIPE
-
INSTALL EGR COOLER WITH PIPE ASSEMBLY
-
INSTALL NO. 2 WATER BY-PASS HOSE
-
INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
-
INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
-
INSTALL VACUUM TRANSMITTING HOSE ASSEMBLY
-
INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY
-
INSTALL VACUUM REGULATING VALVE ASSEMBLY
-
INSTALL NO. 1 TURBO OIL PIPE
-
INSTALL NO. 3 WATER BY-PASS PIPE
-
INSTALL FUEL SUPPLY PUMP ASSEMBLY
-
Apply a light coat of engine oil to a new O-ring.
-
Install a new O-ring to the fuel supply pump assembly.
-
Install the No. 1 supply pump drive coupling.
Note
When reusing the No. 1 supply pump drive coupling, it must be installed in the same orientation (top/bottom, front/back) as when it was removed.
Tech Tips
Line up the No. 1 supply pump drive coupling with the groove in the No. 2 camshaft end.
-
Install the fuel supply pump assembly with the 2 bolts.
- Torque:
- 21 N*m { 209 kgf*cm, 15 ft.*lbf }
Tech Tips
Line up the end of the supply pump drive shaft with the No. 1 supply pump drive coupling.
-
-
INSTALL NO. 3 FUEL HOSE
-
INSTALL FUEL INJECTOR SEAL
-
INSTALL EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
-
INSTALL FUEL TUBE SUB-ASSEMBLY
-
INSTALL FUEL HOSE PROTECTOR
-
INSTALL NO. 2 WATER BY-PASS PIPE
-
INSTALL NO. 4 WATER BY-PASS HOSE
-
INSTALL NO. 8 WATER BY-PASS HOSE
-
INSTALL NO. 6 WATER BY-PASS HOSE
-
INSTALL WATER BY-PASS HOSE
-
INSTALL NO. 1 CYLINDER BLOCK INSULATOR
-
INSTALL GLOW PLUG ASSEMBLY
-
Using a 10 mm deep socket wrench, install the 4 glow plug assemblies.
- Torque:
- 12 N*m { 125 kgf*cm, 9 ft.*lbf }
-
Install the No. 1 glow plug connector with the 4 nuts.
- Torque:
- 2.2 N*m { 22 kgf*cm, 19 in.*lbf }
-
Install the 4 glow plug screw grommets.
-
-
INSTALL INTAKE MANIFOLD
-
INSTALL NO. 2 INTAKE MANIFOLD
-
INSTALL ENGINE COVER BRACKET
-
INSTALL GAS FILTER BRACKET
-
INSTALL NO. 1 GAS FILTER
-
INSTALL DIESEL TURBO PRESSURE SENSOR
-
INSTALL INTAKE MANIFOLD INSULATOR
-
INSTALL COMMON RAIL ASSEMBLY
-
INSTALL NO. 4 FUEL HOSE
-
INSTALL INJECTION PIPE SUB-ASSEMBLY
-
INSTALL FUEL INLET PIPE SUB-ASSEMBLY
-
INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
-
INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY
-
INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY
-
INSTALL EGR VALVE BRACKET
-
CONNECT NO. 8 WATER BY-PASS HOSE
-
INSTALL NO. 7 WATER BY-PASS HOSE
-
INSTALL DIESEL THROTTLE BODY ASSEMBLY
-
INSTALL VACUUM PUMP ASSEMBLY
-
INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
-
INSTALL ENGINE MOUNTING BRACKET
-
INSTALL NO. 4 WATER BY-PASS PIPE
-
INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
-
INSTALL IDLER PULLEY COVER PLATE
-
INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
-
INSTALL GENERATOR ASSEMBLY
-
INSTALL COMPRESSOR STAY
-
Install the compressor stay to the cylinder block sub-assembly.
- Torque:
- 35 N*m { 357 kgf*cm, 26 ft.*lbf }
-
-
INSTALL COOLER COMPRESSOR ASSEMBLY WITH PULLEY
-
INSTALL FAN AND GENERATOR V BELT
-
CONNECT ENGINE WIRE