БЛОК ДВИГАТЕЛЯ РАЗБОРКА

CAUTION / NOTICE / HINT

Note


  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe with a new one.

PROCEDURE


  1. REMOVE NO. 2 NOZZLE LEAKAGE PIPE

    Click here

  2. REMOVE NO. 1 NOZZLE LEAKAGE PIPE

    Click here

  3. REMOVE NO. 1 NOZZLE HOLDER CLAMP

    Click here

  4. REMOVE INJECTOR ASSEMBLY

    Click here

  5. REMOVE CAMSHAFT POSITION SENSOR


    1. A01CXQH

      Remove the bolt and camshaft position sensor.

  6. REMOVE CRANKSHAFT POSITION SENSOR


    1. A01CWTU

      Detach the clip and disconnect the crankshaft position sensor harness.

    2. Remove the 2 bolts and crankshaft position sensor.

  7. REMOVE ENGINE COOLANT TEMPERATURE SENSOR

    Click here

  8. REMOVE ENGINE WATER PUMP ASSEMBLY

    Click here

  9. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY

    Click here

  10. REMOVE OIL COOLER ASSEMBLY

    Click here

  11. REMOVE NO. 1 OIL COOLER BRACKET

    Click here

  12. REMOVE ENGINE OIL LEVEL SENSOR


    1. A01CWZ9

      Remove the 4 bolts and engine oil level sensor.

  13. REMOVE WATER INLET HOUSING

    Click here

  14. REMOVE OIL FILLER CAP SUB-ASSEMBLY

  15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  16. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

    Click here

  17. REMOVE OIL FILTER ELEMENT

    Click here

  18. REMOVE OIL PRESSURE SWITCHING VALVE ASSEMBLY

    Click here

  19. REMOVE OIL FILTER BRACKET

    Click here

  20. REMOVE OIL STRAINER SUB-ASSEMBLY

    Click here

  21. SET NO. 1 CYLINDER TO TDC/COMPRESSION


    1. A01CWHQC06
      *1 Timing Pointer
      *2 Timing Mark

      Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.

    2. A01CYLMC03
      *1 Matchmark
      *2 Timing Mark

      Make sure that the timing mark of the camshaft timing sprocket is at the top.

      Tech Tips

      If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).

    3. Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.

      Tech Tips

      The timing chain has 2 colored plates. If either of them is aligned with the timing mark of the camshaft timing sprocket, this step can be omitted.

    4. A01CYLZN02

      Turn the crankshaft by approximately 90° in the direction of engine revolution from the point where the No. 1 piston is set to TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.

  22. REMOVE CRANKSHAFT PULLEY


    1. A01CWMUN01

      Using SST, hold the crankshaft pulley and loosen the crankshaft pulley bolt.

      SST
      09213-58014   ( 91551-80840 )
      09330-00021
    2. A01CYWIE01

      Using SST, remove the crankshaft pulley bolt and crankshaft pulley.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

  23. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

    Click here

  24. REMOVE FRONT CRANKSHAFT OIL SEAL

    Click here

  25. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    1. A01CYN9C01
      *1 Plunger
      *2 Stopper Plate

      Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.

    2. Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

      SST
      09240-00020   ( 09242-00200 )
    3. A01CW51

      Remove the 2 bolts and No. 1 chain tensioner assembly.

  26. REMOVE CHAIN TENSIONER SLIPPER

    A01CWP2

  27. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    1. A01CXM8

      Remove the 2 bolts and No. 1 chain vibration damper.

  28. REMOVE CAMSHAFT TIMING SPROCKET


    1. A01CXY7

      Remove the 4 bolts from the camshaft timing sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.

    2. Remove the camshaft timing sprocket and chain sub-assembly.

  29. REMOVE OIL PUMP DRIVE GEAR


    1. A01CYYL

      Remove the oil pump drive gear from the crankshaft.

  30. REMOVE CRANKSHAFT TIMING SPROCKET


    1. A01CY5H

      Remove the crankshaft timing sprocket from the crankshaft.

  31. REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY


    1. A01CWMY

      Remove the 2 crankshaft pulley set crankshaft keys from the crankshaft.

  32. REMOVE CAMSHAFT

    Click here

  33. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    Click here

  34. REMOVE VALVE LASH ADJUSTER ASSEMBLY

    Click here

  35. REMOVE CYLINDER HEAD SUB-ASSEMBLY

    Click here

  36. REMOVE CYLINDER HEAD GASKET

  37. REMOVE REAR ENGINE OIL SEAL

    Click here

  38. REMOVE OIL BAFFLE PLATE


    1. A01CXGR

      Remove the 4 bolts and oil baffle plate.

  39. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    1. A01CWDK

      Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.