МАСЛО И МАСЛЯНЫЙ ФИЛЬТР ЗАМЕНА

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will cause removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves. Wash your skin thoroughly with soap and water, or use a waterless hand cleaner to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • For environmental protection, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

    3. Clean and install the oil pan drain plug together with a new gasket.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. REMOVE OIL FILTER


    1. for Oil Filter Element Kit Type:


      1. A01QOFEC01
        *1 Cap Rib
        *2 Oil Filter Bracket Clip

        Using SST, loosen the oil filter cap 4 revolutions, align the cap ribs vertically, and drain the remaining engine oil in the oil filter cap assembly.

        SST
        09228-06501

        Note

        Do not remove the oil filter bracket clip when removing the oil filter cap assembly.

        Tech Tips

        Set a container below the oil filter cap before loosening the oil filter cap assembly.

      2. Remove the oil filter cap assembly.

      3. A01QSE0C01
        *1 Oil Filter Element
        *2 O-Ring

        Remove the oil filter element and O-ring from the oil filter cap.

        Note

        Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.

    2. for Oil Filter Sub-assembly Type:


      1. A01QRQ5N01

        Using SST, remove the oil filter sub-assembly.

        SST
        09228-06501

  3. INSTALL OIL FILTER


    1. for Oil Filter Element Kit Type:


      1. A01QSTIC09
        *1 O-Ring
        *a CORRECT
        *b INCORRECT

        Clean the inside of the oil filter cap, its threads and O-ring groove.

      2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

        Note


        • Be sure to install the O-ring in the proper location, otherwise oil may leak.

        • Do not twist the O-ring.

      3. Set a new oil filter element in the oil filter cap assembly.

      4. Remove any dirt or foreign matter from the installation surface and inside of the engine.

      5. A01QPIL

        Reapply a small amount of engine oil to the O-ring of the oil filter cap. Align the oil filter cap with the oil filter bracket so that the cutout portion of the cap threads is in a position 90° from the groove in the bracket, and then temporarily install the cap.

        Note

        Make sure that the O-ring does not get caught between the parts.

      6. A01QP26C01
        *1 Oil Filter Cap
        *2 O-Ring
        *3 Oil Filter Bracket
        *a No Gap

        Using SST, tighten the oil filter cap assembly.

        SST
        09228-06501
        Torque:
        25 N*m  { 255 kgf*cm, 18 ft.*lbf }

        Note


        • After tightening the oil filter cap, check for gaps between the installation surfaces.

        • Do not remove the oil filter bracket clip when installing the oil filter cap.

        • Do not cross thread the oil filter cap.

        • After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    2. for Oil Filter Sub-assembly Type:


      1. Check and clean the oil filter sub-assembly installation surface.

      2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

      3. Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

      4. A01QSNDN01

        Using SST, tighten the oil filter sub-assembly.

        SST
        09228-06501

          Depending on the work space available, choose from the following:

        • If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }

        • If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or use a common wrench.

  4. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil 15W-40
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 Imp. qts)
      Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 Imp. qts)
      Dry fill 4.7 liters (5.0 US qts, 4.1 Imp. qts)

  5. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  6. INSPECT ENGINE OIL LEVEL

    Click here