РАДИАТОР СНЯТИЕ

PROCEDURE


  1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

    Click here

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  5. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  6. DRAIN ENGINE COOLANT

    Click here

  7. REMOVE FRONT BUMPER COVER

    Click here

  8. REMOVE HEADLIGHT



  9. REMOVE FRONT LOWER BUMPER ABSORBER


    1. B002AIZ

      Remove the 4 screws and front lower bumper absorber.

  10. REMOVE NO. 1 ENGINE COVER

    Click here

  11. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    Click here

  12. REMOVE BATTERY INSULATOR

  13. REMOVE BATTERY

  14. REMOVE BATTERY TRAY

  15. REMOVE FRONT BATTERY BRACKET

    Click here

  16. REMOVE BATTERY BRACKET REINFORCEMENT

    Click here

  17. REMOVE LOW PITCHED HORN ASSEMBLY

    Click here

  18. REMOVE HIGH PITCHED HORN ASSEMBLY

    Click here

  19. REMOVE FRONT BUMPER CENTER STAY SUB-ASSEMBLY


    1. B002AAD

      Remove the 2 bolts, clip and front bumper center stay sub-assembly.

  20. REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

    B002978

    1. Remove the 2 bolts and front bumper upper reinforcement sub-assembly.

  21. REMOVE UPPER RADIATOR AIR GUIDE PLATE


    1. B0029DD

      Remove the 6 clips and upper radiator air guide plate.

  22. REMOVE LOWER RADIATOR AIR GUIDE PLATE


    1. B002ACL

      Detach 3 claws and remove the lower radiator air guide plate.

  23. DISCONNECT AMBIENT THERMISTOR ASSEMBLY


    1. B0029OA

      Detach the clamp to disconnect the ambient thermistor assembly.

  24. REMOVE FRONT BUMPER REINFORCEMENT

    Click here

  25. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

    B002AKI

    1. Remove the bolt and disconnect the discharge hose sub-assembly from the cooler condenser assembly.

    2. Remove the O-ring from the discharge hose sub-assembly.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  26. DISCONNECT LIQUID TUBE SUB-ASSEMBLY

    B0029LT

    1. Remove the bolt and disconnect the liquid tube sub-assembly from the cooler condenser assembly.

    2. Remove the O-ring from the liquid tube sub-assembly.

      Note

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  27. REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH


    1. B0029IJ

      Detach 3 claws and remove the front radiator side air guide plate RH.

  28. REMOVE REAR RADIATOR SIDE AIR GUIDE PLATE RH


    1. B0029JB

      Remove the 2 clips and rear radiator side air guide plate RH.

  29. REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH


    1. B0029DS

      Detach 3 claws and remove the front radiator side air guide plate LH.

  30. REMOVE REAR RADIATOR SIDE AIR GUIDE PLATE LH


    1. B002A17

      Remove the 2 clips and rear radiator side air guide plate LH.

  31. DISCONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY

    B002A3F

    1. Slide the clip and disconnect the No. 2 vacuum transmitting hose assembly from the intake manifold.

  32. REMOVE NO. 1 RADIATOR SUPPORT


    1. B0029L3

      Remove the 2 bolts and 2 No. 1 radiator supports.

    2. Remove the 2 radiator support cushions.

  33. REMOVE NO. 1 WATER BY-PASS HOSE


    1. B002AIF

      Slide the 2 clamps and disconnect the No. 1 water by-pass hose from the radiator reservoir assembly and radiator hose sub-assembly.

    2. Detach the hose clamp from the upper radiator support.

    3. Remove the 2 bolts and disconnect the water by-pass hose clamp bracket from the upper radiator support.

  34. DISCONNECT WIRE HARNESS


    1. B0029P3

      Disconnect the 4 connector and detach the 13 clamps.

  35. REMOVE HOOD LOCK ASSEMBLY



  36. REMOVE UPPER RADIATOR SUPPORT


    1. B002ABW

      Remove the 4 bolts and upper radiator support.

  37. DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

    Click here

  38. DISCONNECT NO. 2 RADIATOR HOSE

    Click here

  39. REMOVE INTERCOOLER AIR HOSE


    1. B0029QW

      Loosen the 2 hose clamps.

    2. Remove the intercooler air hose from the No. 1 air tube and intercooler assembly.

  40. REMOVE NO. 3 AIR HOSE

    Click here

  41. REMOVE RADIATOR ASSEMBLY


    1. B0029X4

      Detach the hose clamp from the oil cooler hose sub-assembly.

    2. Slide the 3 hose clips and disconnect the 3 oil cooler hoses.

    3. Remove the radiator assembly and 2 cushions.

  42. REMOVE NO. 2 RADIATOR SUPPORT


    1. B0029DR

      Remove the 4 bolts and 2 No. 2 radiator supports.

  43. REMOVE COOLER CONDENSER ASSEMBLY


    1. Remove the cooler condenser assembly.

  44. REMOVE NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY


    1. Detach the 4 clamps from the fan shroud and No. 2 air tube.

    2. B0029ZB

      Slide the 2 clips and remove the No. 2 vacuum transmitting hose assembly from the intercooler assembly and No. 2 air tube.

  45. REMOVE NO. 2 AIR TUBE


    1. B002A3N

      Loosen the hose clamp.

    2. Remove the bolt and No. 2 air tube from the intercooler assembly.

  46. REMOVE RADIATOR HOSE SUB-ASSEMBLY


    1. B002ACF

      Disconnect the 2 clamps from the fan shroud.

    2. Slide the 2 clamps and remove the radiator hose sub-assembly from the radiator assembly.

  47. REMOVE NO. 2 RADIATOR HOSE

    B0029W7

    1. Slide the clamp and remove the No. 2 radiator hose from the radiator assembly.

  48. REMOVE OIL COOLER TUBE SUB-ASSEMBLY


    1. B002AEF

      Slide the 2 clips and disconnect the 2 oil cooler hoses from the radiator assembly.

    2. Remove the 2 bolts and oil cooler tube sub-assembly from the fan shroud.

  49. REMOVE LOWER RADIATOR SUPPORT

    Click here

  50. REMOVE INTERCOOLER ASSEMBLY

    Click here

  51. REMOVE FAN SHROUD


    1. B0029BF

      Remove the 3 bolts and fan shroud.