БЛОК ДВИГАТЕЛЯ УСТАНОВКА

PROCEDURE


  1. INSTALL IGNITION COIL ASSEMBLY

    Click here

  2. INSTALL V-BANK COVER BRACKET SUB-ASSEMBLY


    1. Install the V-bank cover bracket sub-assembly to the cylinder head cover sub-assembly RH with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the camshaft housing sub-assembly RH with the bolt.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

  4. INSTALL NO. 3 FUEL PIPE SUB-ASSEMBLY

    Click here

  5. INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

    Click here

  6. INSTALL FUEL PUMP ASSEMBLY

    Click here

  7. CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

    Click here

  8. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

  9. INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

    Click here

  10. INSTALL INTAKE MANIFOLD

    Click here

  11. INSTALL FUEL TUBE SUB-ASSEMBLY


    1. Install the fuel tube sub-assembly with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly and slide the clip to secure it.

      Click here

  12. INSTALL NO. 3 WATER BY-PASS PIPE


    1. Connect the No. 9 water by-pass hose to the rear water by-pass joint and slide the clip to secure it.

    2. Connect the No. 8 water by-pass hose to the water outlet pipe assembly and slide the clip to secure it.

    3. Install the No. 3 water by-pass pipe to the camshaft housing sub-assembly RH with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  13. INSTALL NO. 2 SURGE TANK STAY


    1. Install the No. 2 surge tank stay to the camshaft housing sub-assembly LH with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the 2 clamps to the No. 2 surge tank stay.

  14. INSTALL INTAKE AIR SURGE TANK ASSEMBLY

    Click here

  15. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

  16. INSTALL INJECTOR DRIVER

    Click here

  17. INSTALL ENGINE WIRE


    1. Install the engine wire to the engine assembly.

  18. INSTALL WATER PUMP PULLEY

    Click here

  19. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

  20. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH


    1. Install the front No. 1 engine mounting bracket LH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

    2. Connect the 2 clamps.

  21. INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    1. Install the front No. 1 engine mounting bracket RH to the cylinder block sub-assembly with the 4 bolts.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

  22. INSTALL COMPRESSOR AND MAGNETIC CLUTCH

    Click here

  23. INSTALL GENERATOR ASSEMBLY

    Click here

  24. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

    Click here

  25. INSTALL NO. 1 ENGINE COVER

    Click here

  26. INSTALL NO. 2 ENGINE COVER


    1. Install the No. 2 engine cover with the 3 clips.

    2. Connect the clamp to the No. 2 engine cover.

  27. INSTALL V-RIBBED BELT

    Click here