ПРОКЛАДКА ГОЛОВКИ БЛОКА ЦИЛИНДРОВ УЗЛЫ И ДЕТАЛИ
ILLUSTRATION
| *1 | CHAIN SUB-ASSEMBLY | *2 | CHAIN TENSIONER SLIPPER |
| *3 | NO. 1 CHAIN TENSIONER ASSEMBLY | *4 | NO. 1 CHAIN VIBRATION DAMPER |
| *5 | NO. 2 CHAIN VIBRATION DAMPER | *6 | REAR WATER BY-PASS JOINT |
| *7 | GASKET | *8 | O-RING |
 |
N*m (kgf*cm, ft*lbf) : Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAMSHAFT | *2 | CAMSHAFT HOUSING SUB-ASSEMBLY RH |
| *3 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY | *4 | NO. 2 CAMSHAFT |
| *5 | NO. 2 CHAIN TENSIONER ASSEMBLY | *6 | VALVE LASH ADJUSTER ASSEMBLY |
| *7 | VALVE STEM CAP | *8 | NO. 1 CAMSHAFT BEARING CAP |
| *9 | NO. 2 CAMSHAFT BEARING CAP | *10 | NO. 5 CAMSHAFT BEARING CAP |
| *11 | NO. 6 CAMSHAFT BEARING CAP | *12 | NO. 7 CAMSHAFT BEARING CAP |
| *13 | CAMSHAFT TIMING GEAR ASSEMBLY | *14 | NO. 2 CHAIN SUB-ASSEMBLY |
| *15 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH | - | - |
| |
N*m (kgf*cm, ft*lbf) : Specified torque | - | - |
ILLUSTRATION
| *1 | CAMSHAFT HOUSING SUB-ASSEMBLY LH | *2 | NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
| *3 | NO. 3 CAMSHAFT SUB-ASSEMBLY | *4 | NO. 3 CHAIN TENSIONER ASSEMBLY |
| *5 | NO. 4 CAMSHAFT SUB-ASSEMBLY | *6 | VALVE LASH ADJUSTER ASSEMBLY |
| *7 | VALVE STEM CAP | *8 | NO. 3 CAMSHAFT BEARING CAP |
| *9 | NO. 4 CAMSHAFT BEARING CAP | *10 | NO. 7 CAMSHAFT BEARING CAP |
| *11 | NO. 8 CAMSHAFT BEARING CAP | *12 | CAMSHAFT TIMING GEAR ASSEMBLY |
| *13 | NO. 2 CHAIN SUB-ASSEMBLY | *14 | CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH |
| |
N*m (kgf*cm, ft*lbf) : Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL DELIVERY PIPE SUB-ASSEMBLY | *2 | FUEL INJECTOR ASSEMBLY |
| *3 | FUEL INJECTOR SEAL | *4 | NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY |
| *5 | NO. 3 FUEL PIPE SUB-ASSEMBLY | *6 | NO. 1 BACKUP RING |
| *7 | NO. 2 BACKUP RING | *8 | O-RING |
| *9 | E-RING | *10 | NO. 3 BACKUP RING |
| *11 | NOZZLE HOLDER CLAMP | *12 | INJECTION VIBRATION INSURATOR |
| *13 | WIRE HARNESS | - | - |
| |
N*m (kgf*cm, ft*lbf) : Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD GASKET | *2 | CYLINDER HEAD LH |
| *3 | CYLINDER HEAD SUB-ASSEMBLY | *4 | NO. 2 CYLINDER HEAD GASKET |
| |
N*m (kgf*cm, ft*lbf) : Specified torque | ● | Non-reusable part |
| *T1 | 1st : 36 (367, 27) 2nd : Turn 90° 3rd : Turn 90° |
- | - |