POWER WINDOW REGULATOR MOTOR(for Front Door) INSPECTION

PROCEDURE


  1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

    Note


    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly LH.


    1. A01QUDTC01
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)
      *b Motor Gear
      A01QRKS Clockwise
      A01QOU0 Counterclockwise

      w/ Jam Protection Function:


      1. Check that the motor gear rotates smoothly as follows.

        OK
        Measurement Condition Specified Condition

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

        3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

        		 Motor gear rotates clockwise (UP)

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

        3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

        		 Motor gear rotates counterclockwise (DOWN)

        If the result is not as specified, replace the power window regulator motor assembly LH.

    2. A01QPNYC02
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly LH)
      *b Motor Gear
      A01QRKS Clockwise
      A01QOU0 Counterclockwise

      w/o Jam Protection Function:


      1. Apply battery voltage to connector terminals 1 (D) and 2 (U).

        Note

        Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

    3. Check that the motor gear rotates smoothly as follows.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) → 2 (U)

      Battery negative (-) → 1 (D)

      		 Motor gear rotates clockwise

      Battery positive (+) → 1 (D)

      Battery negative (-) → 2 (U)

      		 Motor gear rotates counterclockwise

      If the result is not as specified, replace the power window regulator motor assembly LH.

  2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

    Note


    • Do not apply positive (+) battery voltage to any terminals, except terminal 2 (B), to avoid damaging the pulse sensor inside the motor.

    • Perform initialization of the power window system after removing, inspecting or replacing the power window regulator motor assembly RH.


    1. A01QQBAC01
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)
      *b Motor Gear
      A01QRKS Clockwise
      A01QOU0 Counterclockwise

      w/ Jam Protection Function:


      1. Check that the motor gear rotates smoothly as follows.

        OK:
        Measurement Condition Specified Condition

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 10 (UP).

        3. After disconnecting the negative (-) lead of the battery from terminal 10 (UP), connect terminal 10 (UP) to the negative (-) lead of the battery again within 1 sec.

        		 Motor gear rotates counterclockwise (UP)

        1. Connect the positive (+) lead of the battery to terminal 2 (B) and the negative (-) lead to terminal 1 (GND), and hold for 3 sec. or more.

        2. While terminals 2 (B) and 1 (GND) are connected, connect the negative (-) lead of the battery to terminal 7 (DOWN).

        3. After disconnecting the negative (-) lead of the battery from terminal 7 (DOWN), connect terminal 7 (DOWN) to the negative (-) lead of the battery again within 1 sec.

        		 Motor gear rotates clockwise (DOWN)

        If the result is not as specified, replace the power window regulator motor assembly RH.

    2. A01QUADC05
      *a

      Component without harness connected

      (Power Window Regulator Motor Assembly RH)
      *b Motor Gear
      A01QRKS Clockwise
      A01QOU0 Counterclockwise

      w/o Jam Protection Function:


      1. Apply battery voltage to connector terminals 1 (D) and 2 (U).

        Note

        Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

      2. Check that the motor gear rotates smoothly as follows

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → 1 (D)

        Battery negative (-) → 2 (U)

        		 Motor gear rotates clockwise

        Battery positive (+) → 2 (U)

        Battery negative (-) → 1 (D)

        		 Motor gear rotates counterclockwise

        If the result is not as specified, replace the power window regulator motor assembly RH.