POWER WINDOW REGULATOR MOTOR(for Front Door) INSPECTION

PROCEDURE

1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

   
   

   1. w/ Jam Protection Function:

      
      
      1. 

         *1	Motor Gear
         *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
         	Clockwise
         	Counterclockwise

         Apply positive (+) battery voltage to the connector terminal 2 (B).

      2. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).

         Note

         
         

         • Do not apply voltage to any terminals except terminals 1 and 2, to avoid damaging the pulse sensor inside the motor.

         
         

         • Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.

      3. Check that the motor gear rotates smoothly as follows.

         OK

         Measurement Condition Specified Condition Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 10 (UP) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 10 (UP) Motor gear rotates clockwise (UP) Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 7 (DOWN) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 7 (DOWN) Motor gear rotates counterclockwise (DOWN)

   2. w/o Jam Protection Function:

      
      
      1. 

         *1	Motor Gear
         *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
         	Clockwise
         	Counterclockwise

         Apply battery voltage to connector terminals 1 (D) and 2 (U).

         Note

         Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

   3. Check that the motor gear rotates smoothly as follows.

      OK
      Measurement Condition Specified Condition Battery positive (+) → 2 (U) Battery negative (-) → 1 (D) Motor gear rotates clockwise Battery positive (+) → 1 (D) Battery negative (-) → 2 (U) Motor gear rotates counterclockwise

      If the result is not as specified, replace the power window regulator motor assembly LH.

2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

   
   

   1. w/ Jam Protection Function:

      
      
      1. 

         *1	Motor Gear
         *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
         	Clockwise
         	Counterclockwise

         Apply positive (+) battery voltage to the connector terminal 2 (B).

      2. Apply negative (-) battery voltage to the connector terminals 1 (GND) and 7 (DOWN) / 10 (UP).

         Note

         
         

         • Do not apply voltage to any terminals except terminals 1 and 2, to avoid damaging the pulse sensor inside the motor.

         
         

         • Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.

      3. Check that the motor gear rotates smoothly as follows.

         OK

         Measurement Condition Specified Condition Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 10 (UP) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 10 (UP) Motor gear rotates clockwise (UP) Battery positive (+) → 2 (B) Battery negative (-): 1 (GND) (3 seconds or more) → 1 (GND) and 7 (DOWN) (within 1 second) → 1 (GND) (within 1 second) → 1 (GND) and 7 (DOWN) Motor gear rotates counterclockwise (DOWN)

   2. w/o Jam Protection Function:

      
      
      1. 

         *1	Motor Gear
         *a	Component without harness connected (Power Window Regulator Motor Assembly RH)
         	Clockwise
         	Counterclockwise

         Apply battery voltage to connector terminals 1 (D) and 2 (U).

         Note

         Do not apply battery voltage to any terminals except terminals 1 (D) and 2 (U).

      2. Check that the motor gear rotates smoothly as follows

         OK
         Measurement Condition Specified Condition Battery positive (+) → 1 (D) Battery negative (-) → 2 (U) Motor gear rotates clockwise Battery positive (+) → 2 (U) Battery negative (-) → 1 (D) Motor gear rotates counterclockwise

         If the result is not as specified, replace the power window regulator motor assembly RH.