POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION

When the ignition switch is ON, the rear power window regulator motor assembly RH is operated by the rear power window regulator switch assembly RH.

WIRING DIAGRAM

A00YR4SE05

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE


  1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    1. Remove the rear power window regulator switch assembly RH.

      Click here

    2. Inspect the rear power window regulator switch assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH Click here

    OK

  2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    1. Remove the rear power window regulator motor assembly RH.

      Click here

    2. Inspect the rear power window regulator motor assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)


    1. A00YQXGC06
      *a

      Front view of wire harness connector

      (to Rear Power Window Regulator Switch Assembly RH)

      Disconnect the rear power window regulator switch assembly RH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      K1-3 (B) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)


    1. Disconnect K3 the rear power window regulator motor assembly RH connector.

    2. Disconnect K1 the rear power window regulator switch assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K3-1 (U) - K1-4 (U) Always Below 1 Ω
      K3-2 (D) - K1-1 (D) Always Below 1 Ω
      K3-1 (U) or K1-4 (U) - Body ground Always 10 kΩ or higher
      K3-2 (D) or K1-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)


    1. Disconnect the K1 rear power window regulator switch assembly RH connector.

    2. Disconnect the J5 rear power window regulator master switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K1-5 (SU) - J5-10 (U) Always Below 1 Ω
      K1-2 (SD) - J5-18 (D) Always Below 1 Ω
      K1-5 (SU) or J5-10 (U) - Body ground Always 10 kΩ or higher
      K1-2 (SD) or J5-18 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR