POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is operated by the power window regulator switch assembly.

WIRING DIAGRAM

A01QTD9E01

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE


  1. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. Remove the power window regulator switch assembly.

      Click here

    2. Inspect the power window regulator switch assembly.

      Click here

      Result
      Proceed to
      OK (for LHD)
      OK (for RHD)
      NG

    OK (for RHD)

    INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    OK (for LHD)

  2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


    1. Remove the front power window regulator motor assembly RH.

      Click here

    2. Inspect the front power window regulator motor assembly RH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BATTERY)


    1. A01QP1MC01
      *a

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)

      Disconnect the power window regulator switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      I4-3 (B) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the I4 power window regulator switch assembly connector.

    2. Disconnect the I2 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I4-4 (U) - I2-2 (U) Always Below 1 Ω
      I4-1 (D) - I2-1 (D) Always Below 1 Ω
      I4-4 (U) or I2-2 (U) - Body ground Always 10 kΩ or higher
      I4-1 (D) or I2-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)


    1. Disconnect the J5 power window regulator master switch assembly connector.

    2. Disconnect the I4 power window regulator switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J5-16 (U) - I4-5 (SU) Always Below 1 Ω
      J5-15 (D) - I4-2 (SD) Always Below 1 Ω
      J5-16 (U) or I4-5 (SU) - Body ground Always 10 kΩ or higher
      J5-15 (D) or I4-2 (SD) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. Remove the front power window regulator motor assembly LH.

      Click here

    2. Inspect the front power window regulator motor assembly LH.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - BATTERY)


    1. A01QP1MC04
      *a

      Front view of wire harness connector

      (to Power Window Regulator Switch Assembly)

      Disconnect the power window regulator switch assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      J4-3 (B) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the J4 power window regulator switch assembly connector.

    2. Disconnect the J2 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J4-4 (U) - J2-2 (U) Always Below 1 Ω
      J4-1 (D) - J2-1 (D) Always Below 1 Ω
      J4-4 (U) or J2-2 (U) - Body ground Always 10 kΩ or higher
      J4-1 (D) or J2-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)


    1. Disconnect the I5 power window regulator master switch assembly connector.

    2. Disconnect the J4 power window regulator switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I5-12 (U) - J4-5 (SU) Always Below 1 Ω
      I5-13 (D) - J4-2 (SD) Always Below 1 Ω
      I5-12 (U) or J4-5 (SU) - Body ground Always 10 kΩ or higher
      I5-13 (D) or J4-2 (SD) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR