POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) Driver Side Power Window does not Operate with Power Window Master Switch

DESCRIPTION

When the ignition switch is ON, the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) is operated by the power window regulator master switch assembly. The front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has motor and ECU functions.

WIRING DIAGRAM

A00YVIDE01

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

    Click here

  • If the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has been replaced with a new one, initialize the power window control system.

    Click here

  • When the ECU determines that the front power window regulator motor assembly LH (for LHD) or front power window regulator motor assembly RH (for RHD) has a malfunction, DTC B2311 is stored.

PROCEDURE


  1. CHECK FOR DTC


    1. Clear the DTC.

      Click here


      Body Electrical > D-Door Motor > Clear DTCs

    2. Check for DTCs.

      Click here


      Body Electrical > D-Door Motor > Trouble Codes
      Result
      Proceed to
      DTC is not output
      DTC is output

    DTC is output

    GO TO DIAGNOSTIC TROUBLE CODE CHART Click here

    DTC is not output

  2. PERFORM ACTIVE TEST USING GTS


    1. Perform the Active Test according to the display on the GTS.

      Click here

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


      Body Electrical > D-Door Motor > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Power Window Driver door power window OFF, UP or DOWN -

      Tech Tips

      Up and down movement does not occur if the arrow is not pressed and held.


      Body Electrical > D-Door Motor > Active Test
      Tester Display
      Power Window
      OK
      Driver door power window operates normally.
      Result
      Proceed to
      OK
      NG (for LHD)
      NG (for RHD)

    NG (for LHD)

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND) Click here

    NG (for RHD)

    CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND) Click here

    OK

  3. READ VALUE USING GTS


    1. Read the Data List according to the display on the GTS.

      Click here


      Body Electrical > D-Door Motor > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      D Door P/W Up SW Driver door power window manual up switch signal ON or OFF

      ON: Driver door power window manual up switch being operated

      OFF: Driver door power window manual up switch not being operated

      		 -
      D Door P/W Down SW Driver door power window manual down switch signal ON or OFF

      ON: Driver door power window manual down switch being operated

      OFF: Driver door power window manual down switch not being operated

      		 -

      Body Electrical > D-Door Motor > Data List
      Tester Display
      D Door P/W Up SW
      D Door P/W Down SW
      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK (for LHD)
      OK (for RHD)
      NG

    OK (for LHD)

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    OK (for RHD)

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

    INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

  4. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND)


    1. A00YSRHC01
      *a

      Front view of wire harness connector

      (to Front Power Window Regulator Motor Assembly LH)

      Disconnect the front power window regulator motor assembly LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J3-1 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      J3-2 (B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  5. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. Remove the power window regulator master switch assembly.

      Click here

    2. Inspect the power window regulator master switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)


    1. A00YRO2C01
      *A for LHD
      *B for RHD
      *a

      Front view of wire harness connector

      (to Power Window Regulator Master Switch Assembly)

      Disconnect the power window regulator master switch assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      J5-1 (E) - Body ground Always Below 1 Ω
      for RHD
      Tester Connection Condition Specified Condition
      I5-9 (E) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Switch Condition Specified Condition
      J5-6 (B) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      for RHD
      Tester Connection Switch Condition Specified Condition
      I5-6 (B) - Body ground Ignition switch ON 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK (for LHD)
      OK (for RHD)
      NG

    OK (for RHD)

    CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK (for LHD)

  7. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)


    1. Disconnect the J5 power window regulator master switch assembly connector.

    2. Disconnect the J3 front power window regulator motor assembly LH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J5-8 (U) - J3-10 (UP) Always Below 1 Ω
      J5-5 (D) - J3-7 (DOWN) Always Below 1 Ω
      J5-8 (U) or J3-10 (UP) - Body ground Always 10 kΩ or higher
      J5-5 (D) or J3-7 (DOWN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)


    1. A00YSRHC02
      *a

      Front view of wire harness connector

      (to Power Window Regulator Motor Assembly RH)

      Disconnect the front power window regulator motor assembly RH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I3-1 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I3-2 (B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)


    1. Disconnect the I5 power window regulator master switch assembly connector.

    2. Disconnect the I3 front power window regulator motor assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I5-1 (U) - I3-10 (UP) Always Below 1 Ω
      I5-5 (D) - I3-7 (DOWN) Always Below 1 Ω
      I5-1 (U) or I3-10 (UP) - Body ground Always 10 kΩ or higher
      I5-5 (D) or I3-7 (DOWN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR