ROOF HEADLINING INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart.

Click here

PROCEDURE


  1. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 3 clips to install the rear No. 2 side rail spacer LH.

  2. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  3. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)


    1. Attach the 2 clips to install the rear No. 2 side rail spacer LH.

    2. Attach the wire harness clamp.

    3. Connect the rear part of the curtain shield airbag assembly LH with a new clip.

    4. A01QSXYC01
      *1 Pin

      Push in the pin to lock the clip.

    5. Check that the curtain shield airbag assembly LH is not twisted.

  4. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  5. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 4 clips to install the rear side rail spacer LH.

  6. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL REAR SIDE RAIL SPACER LH (w/ Curtain Shield Airbag)


    1. Attach the clip to install the rear side rail spacer LH.

    2. Install the bolt.

    3. Install the curtain shield airbag assembly LH.

      Click here

  8. INSTALL REAR SIDE RAIL SPACER RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. Attach the 4 clips to install the front side rail spacer LH.

  10. INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL ROOF HEADLINING ASSEMBLY


    1. Place the roof headlining assembly into the vehicle as shown in the illustration.

      Note

      Be careful not to damage the roof headlining assembly when placing it.

      A01QPUT
    2. A01QOXFC01
      *A w/o Sliding Roof

      w/o Sliding Roof:

      Install the roof headlining assembly with the 5 clips.

    3. w/ Sliding Roof:

      Install the roof headlining assembly with the 3 clips.

    4. Attach the 3 wire harness clamps and connect the 2 connectors to the front pillar LH.

    5. Attach the 4 wire harness clamps to the front pillar RH.

    6. Connect the connector to the rear pillar RH.

    7. w/ Sliding Roof:

      Connect the connector.

    8. w/ EC Mirror:

      Connect the connector.

  12. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

    A01QOZSC01
    *a Joint Portion of the Sun Roof Opening Trim Moulding
    *b Cutout of the Roof Headlining Assembly

    1. Align the joint portion of the sun roof opening trim moulding with the cutout of the roof headlining assembly, and wedge the moulding onto the vehicle body and roof headlining to install it.

  13. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. Attach the 8 claws to install the inner rear view mirror cover.

  14. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

    Click here

  15. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for all assist grip assemblies.


    1. Install the 2 clips and 2 assist grip covers to the assist grip.

    2. Attach the 2 clips to install the assist grip assembly.

  16. INSTALL MAP LIGHT ASSEMBLY

    Click here

  17. INSTALL VISOR HOLDER

    Tech Tips

    Use the same procedure for both visor holders.


    1. A01QS53

      Attach the 2 claws.

    2. Push in the visor holder to install it.

  18. INSTALL VISOR ASSEMBLY LH


    1. Install the visor assembly LH with the 2 screws.

  19. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. INSTALL UPPER INSTRUMENT PANEL

    Click here

  21. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    A01QOXP

    1. Attach the 3 guides.

    2. Attach the upper part of the front pillar garnish assembly LH and the 2 clips to install the front pillar garnish LH.

  22. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)


    1. Install the front pillar garnish clips to the front pillar garnish LH.

      Tech Tips

      Install the front pillar garnish clips so that it faces as shown in the illustration.

      A01QTK1C01
      *a CORRECT *b INCORRECT
    2. A01QSBC

      Attach the 3 guides.

    3. A01QU5LC01
      *1 Front Pillar Garnish Clip

      Attach the 2 front pillar garnish clips to install the front pillar garnish LH.

      Tech Tips

      Make sure that the curtain shield airbag assembly LH is not pinched.

  24. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

    Tech Tips

    Use the same procedure described for the LH side.

  25. INSTALL CENTER PILLAR GARNISH LH


    1. Pass the front seat outer belt floor anchor through the hole of the center pillar garnish LH.

    2. Attach the clip to install the center pillar garnish LH.

    3. Install the 2 clips.

  26. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  27. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. Attach the 2 claws and 2 clips to install the lower center pillar garnish LH.

    2. Connect the front seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  28. INSTALL OUTER LAP BELT ANCHOR COVER

    Click here

  29. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. INSTALL SHOULDER BELT ANCHOR COVER RH

    Click here

  31. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY LH


    1. Attach the 8 clips to install the inner roof side garnish assembly LH.

    2. Connect the rear seat outer belt shoulder anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  32. INSTALL INNER ROOF SIDE GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  33. INSTALL SEAT BELT ANCHOR COVER CAP

    Click here

  34. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. Attach the 4 clips and 6 claws to install the deck trim side panel assembly LH.

    3. Install the luggage hold belt striker assembly with the bolt.

    4. Install the tether anchor set bracket with the bolt.

    5. Close the tether anchor set bracket cover.

    6. Connect the rear seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    7. Install the 2 bolts and screw.

      A01QP3J

  35. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Attach the 4 clips and 6 claws to install the deck trim side panel assembly RH.

    2. Install the luggage hold belt striker assembly with the bolt.

    3. Install the tether anchor set bracket with the bolt.

    4. Close the tether anchor set bracket cover.

    5. Connect the rear seat outer belt floor anchor with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    6. Install the 2 bolts and screw.

      A01QP4L

  36. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01QRM5C01
      *1 Paint Mark
      *2 Mark Position

      Align the paint mark on the rear door opening trim weatherstrip LH with the mark position on the vehicle and install the rear door opening trim weatherstrip LH as shown in the illustration.

  37. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  38. INSTALL REAR DOOR SCUFF PLATE LH


    1. Attach the 6 clips and 2 claws to install the rear door scuff plate LH.

  39. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  40. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01QPJAC01
      *1 Paint Mark
      *2 Mark Position

      Align the paint mark on the front door opening trim weatherstrip LH with the mark position on the vehicle and install the front door opening trim weatherstrip LH as shown in the illustration.

  41. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  42. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 2 clips and 8 claws to install the front door scuff plate LH.

  43. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  44. INSTALL REAR SEAT ASSEMBLY

    for LH Side:

    Click here

    for RH Side:

    Click here

  45. INSTALL REAR NO. 1 FLOOR MAT SUPPORT SIDE PLATE


    1. Attach the 4 clips to install the rear No. 1 floor mat support side plate together with the rear No. 1 floor board.

    2. Install the 4 screws.

    3. Close the No. 1 rear floor board.

  46. INSTALL REAR FLOOR FINISH PLATE (w/o Spare Tire, for Compact Spare Tire)


    1. Attach the 2 guides, 4 clips and 2 claws to install the rear floor finish plate.

  47. INSTALL REAR DECK TRIM COVER (w/ Full Size Spare Tire)


    1. Attach the 4 clips and 4 claws to install the rear deck trim cover.

  48. INSTALL DECK FLOOR BOX LH


    1. Attach the 4 claws to install the deck floor box LH.

    2. Install the 3 clips.

  49. INSTALL DECK BOARD ASSEMBLY


    1. Install the deck board assembly.

  50. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. A01QRLY

      Attach the 2 locks to install the tonneau cover assembly.

  51. INSTALL PACKAGE TRAY TRIM POCKET SUB-ASSEMBLY (w/ Partition Net)


    1. A01QSDL

      Attach the 4 locks to install the package tray trim pocket sub-assembly.

  52. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  53. CHECK SRS WARNING LIGHT

    Click here